Introducción

How to remove the circuit board from an LG CG180 cell phone.

Power down the cell phone by pressing and holding down the red "end call" button.
  • Power down the cell phone by pressing and holding down the red "end call" button.

Agregar Comentario

Turn the phone screen-down so you are looking at the back cover.
  • Turn the phone screen-down so you are looking at the back cover.

Agregar Comentario

Slide the back cover down using your finger to remove the cover from the phone. Slide the back cover down using your finger to remove the cover from the phone.
  • Slide the back cover down using your finger to remove the cover from the phone.

Agregar Comentario

Place your finger at the top of the battery in small gap.
  • Place your finger at the top of the battery in small gap.

Agregar Comentario

Press downward while pulling outward to remove the battery.
  • Press downward while pulling outward to remove the battery.

Agregar Comentario

Remove all four screws on the back of the phone using a Phillips #00 screwdriver.
  • Remove all four screws on the back of the phone using a Phillips #00 screwdriver.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Insert a plastic opening tool in the seam.
  • Insert a plastic opening tool in the seam.

Agregar Comentario

Run the tool along the seam to release all the tabs. Run the tool along the seam to release all the tabs.
  • Run the tool along the seam to release all the tabs.

Agregar Comentario

Pull the phone back cover off once all the tabs are released. Pull the phone back cover off once all the tabs are released.
  • Pull the phone back cover off once all the tabs are released.

Agregar Comentario

Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.
  • Push the contents of the phone away from the hardshell case by applying pressure to the keypad with both thumbs.

Agregar Comentario

The hardshell case is separated from the rest of the phone.
  • The hardshell case is separated from the rest of the phone.

Agregar Comentario

Separate keypad from circuit board by turning it upside down and allowing it to fall off. Separate keypad from circuit board by turning it upside down and allowing it to fall off.
  • Separate keypad from circuit board by turning it upside down and allowing it to fall off.

Agregar Comentario

Place the circuit board with the display facing downward.
  • Place the circuit board with the display facing downward.

Agregar Comentario

Use thumb to release both white clips at the top of the circuit board.
  • Use thumb to release both white clips at the top of the circuit board.

  • Be careful with the display because it is still attached by electrical tape.

Agregar Comentario

Once both clips are released, turn over the circuit board so that the display is facing upward. Carefully lift the display from the left side and open to the right.
  • Once both clips are released, turn over the circuit board so that the display is facing upward.

  • Carefully lift the display from the left side and open to the right.

Agregar Comentario

Carefully remove the electrical tape from the display.
  • Carefully remove the electrical tape from the display.

Agregar Comentario

The display is disconnected from the circuit board.
  • The display is disconnected from the circuit board.

Agregar Comentario

The circuit board is separated from the rest of the phone.
  • The circuit board is separated from the rest of the phone.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Alex Jacobs

Miembro Desde 21/01/10

5 Reputación

8 Guías creadas

Equipo

Cal Poly, Team 14-42, Regan Winter 2010 Miembro de Cal Poly, Team 14-42, Regan Winter 2010

CPSU-REGAN-W10S14G42

4 Miembros

10 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 2,730