Introducción

Removing and replacing the lens.

Partes

No se requieren partes.

Use your finger tip to slide battery cover door away from the center of the camera.
  • Use your finger tip to slide battery cover door away from the center of the camera.

  • The battery door should spring open.

    • If this does not happen, gently open the door lifting from the outer bottom side of the camera.

Agregar Comentario

Remove the old batteries.
  • Remove the old batteries.

Agregar Comentario

Remove 7 screws from the outer case with a Phillips #00. All screws are 4.45mm. There are 2 screws on the port side.
  • Remove 7 screws from the outer case with a Phillips #00.

    • All screws are 4.45mm.

    • There are 2 screws on the port side.

    • There are 2 screws on starboard side.

    • There are 3 screws on the bottom.

Agregar Comentario

Make sure the battery cap is "up". Pull the outer case off with your hands. Pull the outer case off with your hands.
  • Make sure the battery cap is "up".

  • Pull the outer case off with your hands.

Agregar Comentario

The LCD Screen is hinged at the bottom.
  • The LCD Screen is hinged at the bottom.

  • Put your thumb in the upper right corner of the LCD Screen.

    • Pull the LCD screen out of it's outer case with your thumb.

Agregar Comentario

Remove the screw underneath LCD screen with the Phillips #00. The screw measures 4.1mm in length.
  • Remove the screw underneath LCD screen with the Phillips #00. The screw measures 4.1mm in length.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Desolder the two points. One on the port side.
  • Desolder the two points.

    • One on the port side.

    • One on the bottom.

Agregar Comentario

After desoldering the LCD casing, just use your fingers to carefully remove it.
  • After desoldering the LCD casing, just use your fingers to carefully remove it.

Agregar Comentario

Flip up the black tab on the bottom of the LCD Screen with a fingertip.
  • Flip up the black tab on the bottom of the LCD Screen with a fingertip.

Agregar Comentario

Remove the LCD ribbon cable from inside the black tab.
  • Remove the LCD ribbon cable from inside the black tab.

Agregar Comentario

Using a fingertip, flip the black tab near the top of the camera.
  • Using a fingertip, flip the black tab near the top of the camera.

    • Remove the ribbon connector from inside the black tab.

Agregar Comentario

Remove the remaining screws on the back with the Phillips #00.
  • Remove the remaining screws on the back with the Phillips #00.

    • These 8 screws measure 4.1mm in length.

Agregar Comentario

Desolder the upper points.
  • Desolder the upper points.

    • There is a large solder point in the upper right.

    • There is a series of solder points in a rectangular area in the upper middle of the camera.

Agregar Comentario

Turn the camera over.
  • Turn the camera over.

  • Remove the battery cap screw.

    • It is silver and measures 2.2mm.

Agregar Comentario

Turn the camera over. Pry the capacitor out of its holder on the bottom of the camera. This can be done with your fingers.
  • Turn the camera over.

  • Pry the capacitor out of its holder on the bottom of the camera. This can be done with your fingers.

Agregar Comentario

Remove the lens assembly with your fingers. You may need to wiggle it back and forth until it comes loose. Do not touch the marked areas. This will cause the camera to take blurry pictures.
  • Remove the lens assembly with your fingers.

    • You may need to wiggle it back and forth until it comes loose.

  • Do not touch the marked areas. This will cause the camera to take blurry pictures.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Taggart Ashby

Miembro Desde 15/04/10

291 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 26-19, Regan Spring 2010 Miembro de Cal Poly, Team 26-19, Regan Spring 2010

CPSU-REGAN-S10S26G19

4 Miembros

7 Guías creadas

why didn't you mention to discharge the capacitor, its stored charge is pretty high & dangerous

richard - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 5

Todo El Tiempo: 6,135