Wooden crate: Open the shipping crate Wooden crate: Remove the wooden panel to get access to the floor panel
  • Wooden crate: Open the shipping crate

  • Wooden crate: Remove the wooden panel to get access to the floor panel

  • NEW Cardboard crate: If your system is shipped in the new cardboard crate, simply remove the lid and carefully cut open the cardboard (the crate is single use).

Agregar Comentario

Screw the four feet into the bottom of the floor. Put the floor horizontal (use a bubble level)
  • Screw the four feet into the bottom of the floor.

  • Put the floor horizontal (use a bubble level)

Agregar Comentario

Install the rear panel onto the floor panel Note: The rear panel can be recognized because there is a small grey flat cable coming out of the top.
  • Install the rear panel onto the floor panel

  • Note: The rear panel can be recognized because there is a small grey flat cable coming out of the top.

  • Align the rear panel precisely over positioning holes in the floor and lower it carefully until it clicks into place.

  • Use the four shorter M8 bolts to fix the panel onto the floor.

  • WARNING! Be careful not to tilt over the panels. The system is only stable after the roof has been installed.

Agregar Comentario

Repeat the previous step for the left panel Note: The left panel can be recognized because it does not have yellow warning stickers glued to the side.
  • Repeat the previous step for the left panel

  • Note: The left panel can be recognized because it does not have yellow warning stickers glued to the side.

Agregar Comentario

Repeat the previous step for the right panel
  • Repeat the previous step for the right panel

  • Note: The right panel can be recognized because it has 2 yellow warning labels glue to the side.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Remove the top panel from the roof Note: Your top panel make look different. That means you have another iteration of the system.
  • Remove the top panel from the roof

  • Note: Your top panel make look different. That means you have another iteration of the system.

Agregar Comentario

Lift the roof on top of the wall panels (the display should be above the rear panel) Align the panels with the roof and insert long M8 bolts Tighten the bolts to secure the roof (each panel requires four bolts)
  • Lift the roof on top of the wall panels (the display should be above the rear panel)

  • Align the panels with the roof and insert long M8 bolts

  • Tighten the bolts to secure the roof (each panel requires four bolts)

Agregar Comentario

Click the connector at the roof for each panel in the corresponding socket at the top of the rear, left and right side panel On the rear panel, push the grey flat cable carefully through the opening in the roof, and connect it to the CPU module (there is only one open socket on the CPU module).
  • Click the connector at the roof for each panel in the corresponding socket at the top of the rear, left and right side panel

  • On the rear panel, push the grey flat cable carefully through the opening in the roof, and connect it to the CPU module (there is only one open socket on the CPU module).

Agregar Comentario

Install the door (be careful: do NOT lift the door by the plastic door handle!)
  • Install the door (be careful: do NOT lift the door by the plastic door handle!)

  • If the metal pin is not in the door yet, you have to install it at the bottom of the door before proceeding.

  • Align the metal pin at the bottom of the door into the teflon washer at the left side of the floor (see red marker in the photo)

Agregar Comentario

Straighten the door and push the cable at the top of the door through the round hole in the roof and through the round metal peg Slide the round metal peg into the cable opening of the door, actually securing the door Slide the round metal peg into the cable opening of the door, actually securing the door
  • Straighten the door and push the cable at the top of the door through the round hole in the roof and through the round metal peg

  • Slide the round metal peg into the cable opening of the door, actually securing the door

Agregar Comentario

Attach the round connector coming from the door to the round plug in the roof
  • Attach the round connector coming from the door to the round plug in the roof

Agregar Comentario

Close the roof with the metal plate
  • Close the roof with the metal plate

  • Lower the feet of the floor, if required

Agregar Comentario

Attach a power cord (230V / 50 Hz) and test the cabin
  • Attach a power cord (230V / 50 Hz) and test the cabin

Agregar Comentario

Linea de Meta

2 personas más completaron esta guía.

Chris De Laet

Miembro Desde 26/03/13

151 Reputación

1 Guía escrita

Equipo

DELCOMp Miembro de DELCOMp

Community

1 Miembro

1 Guía escrita

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 200