Using a Philips screwdriver, remove the two screws on the top of the device, towards the back.
  • Using a Philips screwdriver, remove the two screws on the top of the device, towards the back.

Agregar Comentario

Remove the plastic cover by pulling up on the back and away from the faceplate. Remove the plastic cover by pulling up on the back and away from the faceplate.
  • Remove the plastic cover by pulling up on the back and away from the faceplate.

Agregar Comentario

Remove the faceplate by unclipping the latches on the bottom of the device. Once it's unlatched, pull the faceplate off. Once it's unlatched, pull the faceplate off.
  • Remove the faceplate by unclipping the latches on the bottom of the device.

  • Once it's unlatched, pull the faceplate off.

Agregar Comentario

Using your philips screwdriver, remove the two screws at the base of the disc drive. (See image) Using your philips screwdriver, remove the two screws at the base of the disc drive. (See image)
  • Using your philips screwdriver, remove the two screws at the base of the disc drive. (See image)

Agregar Comentario

Remove the two screws on either side of the silver security bar. Remove the two screws on either side of the silver security bar.
  • Remove the two screws on either side of the silver security bar.

Agregar Comentario

Remove the silver security bar and set aside. Remove the silver security bar and set aside.
  • Remove the silver security bar and set aside.

Agregar Comentario

Remove the two screws on either side of the green circuit-board as seen in the photos.  Once the screws are removed, gently lift the board so you can remove the disc drive.  BE CAREFUL! The board is still attached to the base of the DVD player.  You just need to lift it enough to pull the disc drive out. Remove the two screws on either side of the green circuit-board as seen in the photos.  Once the screws are removed, gently lift the board so you can remove the disc drive.  BE CAREFUL! The board is still attached to the base of the DVD player.  You just need to lift it enough to pull the disc drive out. Remove the two screws on either side of the green circuit-board as seen in the photos.  Once the screws are removed, gently lift the board so you can remove the disc drive.  BE CAREFUL! The board is still attached to the base of the DVD player.  You just need to lift it enough to pull the disc drive out.
  • Remove the two screws on either side of the green circuit-board as seen in the photos. Once the screws are removed, gently lift the board so you can remove the disc drive. BE CAREFUL! The board is still attached to the base of the DVD player. You just need to lift it enough to pull the disc drive out.

Agregar Comentario

Remove the two screws at the back of the disc drive. Remove the two screws at the back of the disc drive. Remove the two screws at the back of the disc drive.
  • Remove the two screws at the back of the disc drive.

Agregar Comentario

You can now gently lift the disc drive out of the the DVD player.  BE CAREFUL! The disc drive is still attached but you are now able to get to underneath it for cleaning and maintenance. You can now gently lift the disc drive out of the the DVD player.  BE CAREFUL! The disc drive is still attached but you are now able to get to underneath it for cleaning and maintenance.
  • You can now gently lift the disc drive out of the the DVD player. BE CAREFUL! The disc drive is still attached but you are now able to get to underneath it for cleaning and maintenance.

Agregar Comentario

Turn disc drive over so you can see the gears on the bottom. Turn disc drive over so you can see the gears on the bottom.
  • Turn disc drive over so you can see the gears on the bottom.

Agregar Comentario

Using a cotton swap or a cleansing cloth and alcohol, gently rub the gears ridding of any debris and dust. You can also use a compressed air can as well. Just point the nozzle at the gears and spray with the compressed air.
  • Using a cotton swap or a cleansing cloth and alcohol, gently rub the gears ridding of any debris and dust.

  • You can also use a compressed air can as well. Just point the nozzle at the gears and spray with the compressed air.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Taryn

Miembro Desde 15/09/11

103 Reputación

4 Guías creadas

Equipo

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 614