Introducción

Following these instructions will allow you to install a new keyboard.

Partes

No se requieren partes.

Flip the HP iPAQ HW6515 over with the screen facing down. Take the back cover off by pressing on the small silver button while pulling back then up on the case. Place the back of the case aside for now.
  • Flip the HP iPAQ HW6515 over with the screen facing down.

  • Take the back cover off by pressing on the small silver button while pulling back then up on the case.

  • Place the back of the case aside for now.

Agregar Comentario

Remove the battery by pulling up on the black tab.
  • Remove the battery by pulling up on the black tab.

Agregar Comentario

Unscrew the four outside screws using the T6 hexagonal star screwdriver. Unscrew the inside middle screw using a Phillips 00 screwdriver. "Warranty VOID if broken" sticker might be covering the middle screw, if this is the case, peel it off to reveal the screw.
  • Unscrew the four outside screws using the T6 hexagonal star screwdriver.

  • Unscrew the inside middle screw using a Phillips 00 screwdriver.

  • "Warranty VOID if broken" sticker might be covering the middle screw, if this is the case, peel it off to reveal the screw.

Agregar Comentario

Use the plastic opening tool to pry apart the covers along the bottom of the phone. Slide the plastic opening tool along the seam until the two halves of the case separate. Slide the plastic opening tool along the seam until the two halves of the case separate.
  • Use the plastic opening tool to pry apart the covers along the bottom of the phone.

  • Slide the plastic opening tool along the seam until the two halves of the case separate.

Agregar Comentario

Guía de regalos para el día del padre
Honremos a más que nuestros padres—celebremos a todos los mentores que nos enseñaron a reparar.
Guía de regalos para el día del padre
Honremos a aquellos que nos enseñaron a reparar.
Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire. Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire. Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire.
  • Unplug the sensor wire that connects the two halves of the case before pulling the two halves apart. Not doing so will damage the sensor wire.

Agregar Comentario

Use a 00 Phillips screwdriver to remove the three small screws holding down the motherboard.
  • Use a 00 Phillips screwdriver to remove the three small screws holding down the motherboard.

Agregar Comentario

Peel back the black tape that covers the connector.
  • Peel back the black tape that covers the connector.

  • It is fine if one of the left connectors comes off along with the tape.

Agregar Comentario

Lift the black tab to a 45 degree angle. Use a screwdriver to get under the tape and disconnect the tape from the black tab. Use a screwdriver to get under the tape and disconnect the tape from the black tab.
  • Lift the black tab to a 45 degree angle.

  • Use a screwdriver to get under the tape and disconnect the tape from the black tab.

Agregar Comentario

Gently pry the motherboard out of the front casing, bottom first. Disconnect the wire connecting the motherboard to the front casing. Using too much force will damage this wire.
  • Gently pry the motherboard out of the front casing, bottom first.

  • Disconnect the wire connecting the motherboard to the front casing. Using too much force will damage this wire.

Agregar Comentario

Unscrew the four small screws holding the keyboard in place using a 00 Phillips screwdriver.
  • Unscrew the four small screws holding the keyboard in place using a 00 Phillips screwdriver.

Agregar Comentario

Holding the phone in the same orientation as the photo, gently pull off the backing of the keyboard and place it aside. Removing this backing grants you access to the keyboard.
  • Holding the phone in the same orientation as the photo, gently pull off the backing of the keyboard and place it aside. Removing this backing grants you access to the keyboard.

Agregar Comentario

Carefully pop the keyboard out by bending the phone casing to free the keyboard from the casing.
  • Carefully pop the keyboard out by bending the phone casing to free the keyboard from the casing.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Tim

Miembro Desde 03/04/12

88 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 15-17, Forte Spring 2012 Miembro de Cal Poly, Team 15-17, Forte Spring 2012

CPSU-FORTE-S12S15G17

4 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 568