Introducción

Use this guide to replace the hard drive.

With the case closed, place the Mini 1000 top-side down on a flat surface. Push both of the battery release latches toward each other.
  • With the case closed, place the Mini 1000 top-side down on a flat surface.

  • Push both of the battery release latches toward each other.

Agregar Comentario

Lift the battery out of the Mini 1000 from the edge closest to the release latches.
  • Lift the battery out of the Mini 1000 from the edge closest to the release latches.

Agregar Comentario

Remove the following two screws:
  • Remove the following two screws:

    • One 6 mm Phillips screw

    • One 4 mm Phillips screw

Agregar Comentario

To facilitate the removal of the keyboard, it is recommended to push the keyboard outwards with one hand through the opening (highlighted in the third picture) located on the backside of the Mini 1000. While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you. Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.
  • To facilitate the removal of the keyboard, it is recommended to push the keyboard outwards with one hand through the opening (highlighted in the third picture) located on the backside of the Mini 1000.

  • While pushing through the opening with one hand, grasp the left upper edge with the other hand and slightly pull the keyboard towards you.

  • Once an opening has been established, grasp the keyboard and slowly lift it upwards along the upper perimeter of the top edge.

Agregar Comentario

Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.
  • Lift the keyboard out of the upper case, minding the cable that is still connecting it to the motherboard.

Agregar Comentario

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.
  • Use your fingernail or the flat end of a spudger to flip up the retaining flap on the keyboard cable ZIF socket.

  • Be sure you are prying up on the retaining flap, not the socket itself.

  • Pull the cable out of its socket and remove the keyboard.

Agregar Comentario

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket. Be sure you are prying up on the retaining flap, not the socket itself.
  • Use your fingernail or the flat end of a spudger to flip up the retaining flap on the SIM card ribbon cable ZIF socket.

  • Be sure you are prying up on the retaining flap, not the socket itself.

  • Pull the SIM card ribbon cable out of its socket and peel it off the top of the hard drive enclosure.

Agregar Comentario

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.
  • Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.

  • Be sure you are prying up on the retaining flap, not the socket itself.

Agregar Comentario

Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.
  • Remove the two 4.5 mm Phillips screws securing the hard drive to the lower case.

Agregar Comentario

Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process. Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.
  • Lift the hard drive up and out of the lower case, being careful not to damage its cable in the process.

Agregar Comentario

Carefully peel up the two foam bumpers from the ends stuck to the bottom of the hard drive. It is not necessary to peel these bumpers off the hard drive enclosure.
  • Carefully peel up the two foam bumpers from the ends stuck to the bottom of the hard drive.

  • It is not necessary to peel these bumpers off the hard drive enclosure.

Agregar Comentario

Lift up the center retaining tab on the hard drive enclosure and simultaneously push the hard drive out through the open end of the enclosure. Lift up the center retaining tab on the hard drive enclosure and simultaneously push the hard drive out through the open end of the enclosure.
  • Lift up the center retaining tab on the hard drive enclosure and simultaneously push the hard drive out through the open end of the enclosure.

Agregar Comentario

Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket. Be sure you are prying up on the retaining flap, not the socket itself.
  • Use your fingernail or the flat end of a spudger to flip up the retaining flap on the hard drive cable ZIF socket.

  • Be sure you are prying up on the retaining flap, not the socket itself.

  • Pull the hard drive cable out of its socket.

  • Hard drive remains.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

17 personas más completaron esta guía.

Great guild, straight forward and easy to follow. Take care disconnecting the hard drive. The clip slides slightly up and then turns up.

Mark - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 7

Últimos 7 Días: 26

Últimos 30 Días: 119

Todo El Tiempo: 36,639