Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.
  • Locate and remove two 6.4mm screws on the bottom of the camera with a Phillips #00 screwdriver.

Agregar Comentario

Locate the battery door.
  • Locate the battery door.

Agregar Comentario

Locate the latch on the battery door marked by the word "BATT." Use your finger to pry it open.
  • Locate the latch on the battery door marked by the word "BATT." Use your finger to pry it open.

Agregar Comentario

Remove the battery from the camera by pulling the battery door outwards.
  • Remove the battery from the camera by pulling the battery door outwards.

Agregar Comentario

Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.
  • Locate and remove three black 3.80mm screws on the back of the camera with the Phillips #00 screwdriver.

Agregar Comentario

Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver. Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.
  • Locate and remove the 6.4mm screws located on either side of the camera with a Phillips #00 screwdriver.

Agregar Comentario

Locate the film door latch located on the side of the camera.
  • Locate the film door latch located on the side of the camera.

  • Insert the spudger under the latch.

  • Caution: Be careful during the following step in order to not break any parts within the camera. Prying the latch in any other direction than perpendicular may result in broken parts.

  • Pry the latch upward, applying force perpendicular to the camera.

Agregar Comentario

Insert the flat edge of the spudger between the gold front casing and the black back casing.
  • Insert the flat edge of the spudger between the gold front casing and the black back casing.

  • Pry the spudger upward until the black back casing snaps out and is dislodged on that edge of the camera.

Agregar Comentario

Squeeze the camera by placing a thumb on the tab marked CE.
  • Squeeze the camera by placing a thumb on the tab marked CE.

  • Pull the back half of the camera firmly away from the camera body.

Agregar Comentario

Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.
  • Locate and remove the 3.80mm screw inside the film compartment with the Phillips #00 screwdriver.

Agregar Comentario

Pull the front cover off of the camera by lifting the tripod tab over the tripod hole. Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.
  • Pull the front cover off of the camera by lifting the tripod tab over the tripod hole.

Agregar Comentario

Locate the film door on the bottom of the camera.
  • Locate the film door on the bottom of the camera.

  • Locate the pin that connects the film door to the camera

Agregar Comentario

Push the pin from one side with the spudger until it comes out on the opposite side.
  • Push the pin from one side with the spudger until it comes out on the opposite side.

Agregar Comentario

Grab the pin with the tweezers and gently pull it out.
  • Grab the pin with the tweezers and gently pull it out.

  • The film door should feel lose.

Agregar Comentario

Remove the door with your fingers and discard it.
  • Remove the door with your fingers and discard it.

  • Insert the replacement film door appropriately to fit where the broken door was located.

Agregar Comentario

Conclusión

To reassemble your device, follow the instructions from the "Disassembling Fujifilm Endeavor 100ix Outer Casing" guide in reverse order.

Eric Nicolai

Miembro Desde 10/01/11

679 Reputación

6 Guías creadas

Equipo

Cal Poly, Team 13-5, Forte Winter 2011 Miembro de Cal Poly, Team 13-5, Forte Winter 2011

CPSU-FORTE-W11S13G5

5 Miembros

6 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 1

Últimos 30 Días: 2

Todo El Tiempo: 1,570