Partes

No se requieren partes.

Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws) Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)
  • Unscrew the bottom and right side panel screws using a #00 screwdriver. (5 screws)

Put a notice on here that the screws are very small and are easy to misplace while disassembling device. Also, while disassembling the device there was only one screw present, where the guide suggested there were three.

Curtis Reedy - Contestar

Before beginning, put a note that the camera should be turned off before proceeding.

Curtis Reedy - Contestar

Add a note at the beginning of the guide that there are a large number of small screws that should be separated as the steps are completed.

Curtis Reedy - Contestar

There's a capacitor .....watch out for it in every step.

BILL BOYD - Contestar

Remove the right side panel by pulling off the large silver piece.
  • Remove the right side panel by pulling off the large silver piece.

There is no reference to removing screws from the right side panel, where it is necessary to remove 2 screws to do so.

Curtis Reedy - Contestar

Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws) Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)
  • Unscrew the remaining side and front panel screws using a #00 screwdriver. (3 screws)

Agregar Comentario

Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)
  • Using your thumb and forefinger, pull off the silver name plate and silver "T-shape" piece. (2 pieces)

Agregar Comentario

Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.
  • Remove the black front panel by sliding it towards the lens and then pulling it up off the camera.

Agregar Comentario

Remove 3 screws from the front of the camera using a #00 screwdriver. Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side) Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)
  • Remove 3 screws from the front of the camera using a #00 screwdriver.

  • Lift the two tabs to separate the case using a spudger. (one tab on top and one tab on the right side)

Wrong point of focus for the second picture. What should be in focus is very blurry.

Curtis Reedy - Contestar

Using a plastic spudger, lift up the black clips. Still using the plastic spudger, detach the gold connector strip and white connector strip. Using both hands, pull the camera apart into two pieces.
  • Using a plastic spudger, lift up the black clips.

  • Still using the plastic spudger, detach the gold connector strip and white connector strip.

  • Using both hands, pull the camera apart into two pieces.

There were multiple gold strips, so the one that needs to be pulled should be highlited in the picture.

Curtis Reedy - Contestar

in step seven pull up the black bar of the ZIF connectors before pulling out the white or gold ribbons

Curtis Reedy - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

Max McIntyre

Miembro Desde 21/01/11

511 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 13-4, Forte Winter 2011 Miembro de Cal Poly, Team 13-4, Forte Winter 2011

CPSU-FORTE-W11S13G4

6 Miembros

6 Guías creadas

How did you get the ring around the lens off?? I can't seem to find that step and in all the pictures it's already off

Maureen - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 5

Todo El Tiempo: 2,498