Introducción

This guide will show you how to replace a motor tread.

Loosen the screws on the serial port by turning them counter clockwise by hand. After loosening the screws, pull the serial port out. After loosening the screws, pull the serial port out.
  • Loosen the screws on the serial port by turning them counter clockwise by hand.

  • After loosening the screws, pull the serial port out.

Agregar Comentario

Lift lid to its vertical position. Pull lid straight up to remove it from the scanner. Pull lid straight up to remove it from the scanner.
  • Lift lid to its vertical position.

  • Pull lid straight up to remove it from the scanner.

Agregar Comentario

Push the plastic opening tools into the crack between the top and the bottom of the chassis. Push the plastic opening tools into the crack between the top and the bottom of the chassis. Push the plastic opening tools into the crack between the top and the bottom of the chassis.
  • Push the plastic opening tools into the crack between the top and the bottom of the chassis.

Agregar Comentario

After placing one plastic opening tool into the slit, slide other plastic opening tools along the slit to detach the top from the bottom of the chassis. Go all the way along the chassis until you can lift the upper lid. Go all the way along the chassis until you can lift the upper lid.
  • After placing one plastic opening tool into the slit, slide other plastic opening tools along the slit to detach the top from the bottom of the chassis.

  • Go all the way along the chassis until you can lift the upper lid.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Do not fully remove the lid until you remove the ribbon cable attached to the front of the upper lid. Do this by grabbing the upper lid from the sides and rotating it ninety degrees so it is perpendicular to the bottom lid. Grab the ribbon cable and gently pull it out of its slot with your fingers.
  • Do not fully remove the lid until you remove the ribbon cable attached to the front of the upper lid.

  • Do this by grabbing the upper lid from the sides and rotating it ninety degrees so it is perpendicular to the bottom lid.

  • Grab the ribbon cable and gently pull it out of its slot with your fingers.

  • The upper lid can now safely be removed from the bottom lid.

Agregar Comentario

Locate the stepper motor. With the front of the scanner facing you, the motor is located at the top left. Disconnect the white connector from the vertical standing circuit board.
  • Locate the stepper motor. With the front of the scanner facing you, the motor is located at the top left.

  • Disconnect the white connector from the vertical standing circuit board.

Agregar Comentario

Using a #2 Philips Screwdriver, unscrew the two 7.7mm screws holding the stepper motor in place. The stepper motor will become loose, but not completely free. The stepper motor will become loose, but not completely free.
  • Using a #2 Philips Screwdriver, unscrew the two 7.7mm screws holding the stepper motor in place.

  • The stepper motor will become loose, but not completely free.

Agregar Comentario

Using tweezers gently remove the tread from the black gear on the stepper motor. The stepper motor will become completely free. The stepper motor will become completely free.
  • Using tweezers gently remove the tread from the black gear on the stepper motor.

  • The stepper motor will become completely free.

Agregar Comentario

Facing the front of the scanner you will see a white plastic wheel holding the other end of the tread. Pull the spring towards you until it snaps off the side wall releasing the tension in the spring.
  • Facing the front of the scanner you will see a white plastic wheel holding the other end of the tread.

  • Pull the spring towards you until it snaps off the side wall releasing the tension in the spring.

  • Using a #2 Philips Screwdriver, unscrew the single 5.88mm screw holding the mount of the plastic wheel in place.

Agregar Comentario

The plastic wheel and it's mount will be loose.
  • The plastic wheel and it's mount will be loose.

  • Remove the shaft holding the plastic wheel and the mount together

  • The tread will be completely loose.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Equipo

Cal Poly, Team 6-9, Regan Fall 2011 Miembro de Cal Poly, Team 6-9, Regan Fall 2011

CPSU-REGAN-F11S6G9

2 Miembros

11 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 1,175