Introducción

These instructions will demonstrate how to remove the logic board from the KDDI Kyocera A5521K.

Turn the phone over to expose the battery cover. Apply pressure to the back of the battery cover to slide it down. The battery cover is now separate from the phone.
  • Turn the phone over to expose the battery cover.

  • Apply pressure to the back of the battery cover to slide it down.

  • The battery cover is now separate from the phone.

Agregar Comentario

Remove the battery by pushing it up and out from the bottom. The battery, cover, and phone should now be separated. The battery, cover, and phone should now be separated.
  • Remove the battery by pushing it up and out from the bottom.

  • The battery, cover, and phone should now be separated.

Agregar Comentario

Remove the four screws with the Y0 screwdriver. Remove the four screws with the Y0 screwdriver.
  • Remove the four screws with the Y0 screwdriver.

Agregar Comentario

Remove the black, rubber screw caps towards the top of the back of the phone to reveal two additional screws. Remove the two screws with a Y0 screwdriver.
  • Remove the black, rubber screw caps towards the top of the back of the phone to reveal two additional screws.

  • Remove the two screws with a Y0 screwdriver.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Rotate the phone 180 degrees. Carefully separate the back plate from the remainder of the phone. The back plate should now be detached from the rest of the phone.
  • Rotate the phone 180 degrees.

  • Carefully separate the back plate from the remainder of the phone.

  • The back plate should now be detached from the rest of the phone.

Agregar Comentario

Rotate the phone approximately 45 degrees to the right. Gently pry up the SD card slot with a spudger. Gently pry up the SD card slot with a spudger.
  • Rotate the phone approximately 45 degrees to the right.

  • Gently pry up the SD card slot with a spudger.

Agregar Comentario

Lift up on the first connection shown using a pair of pliers. Disconnect the first connection between the logic board and the wire using the pair of pliers. Disconnect the first connection between the logic board and the wire using the pair of pliers.
  • Lift up on the first connection shown using a pair of pliers.

  • Disconnect the first connection between the logic board and the wire using the pair of pliers.

Agregar Comentario

Repeat the above steps for the second connection. Use the pliers to pry up the connection. Use the pliers to disconnect the connection between the logic board and the wire.
  • Repeat the above steps for the second connection.

  • Use the pliers to pry up the connection.

  • Use the pliers to disconnect the connection between the logic board and the wire.

Agregar Comentario

Lift up on the bottom of the logic board with a spudger.
  • Lift up on the bottom of the logic board with a spudger.

  • Gently remove the rest of the logic board from the phone.

Agregar Comentario

The logic board should now be completely disconnected from the phone. The logic board should now be completely disconnected from the phone.
  • The logic board should now be completely disconnected from the phone.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Dominic Grisafe

Miembro Desde 15/04/10

133 Reputación

20 Guías creadas

Equipo

Cal Poly, Team 28-25, Regan Spring 2010 Miembro de Cal Poly, Team 28-25, Regan Spring 2010

CPSU-REGAN-S10S28G25

4 Miembros

20 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 6

Últimos 7 Días: 31

Últimos 30 Días: 38

Todo El Tiempo: 1,347