Press the eject button to view the laser inside. Using the blue plastic tool and the tweezers, remove the ribbon cable. Using the blue plastic tool and the tweezers, remove the ribbon cable.
  • Press the eject button to view the laser inside.

  • Using the blue plastic tool and the tweezers, remove the ribbon cable.

Agregar Comentario

Remove the six 1cm screws on the bottom of the device with the Phillips #1 screwdriver. Do not lift the top of the DVD player too quickly because there are wires attached on the inside. Pry the top of the device open from the right side where the buttons are located.
  • Remove the six 1cm screws on the bottom of the device with the Phillips #1 screwdriver.

  • Do not lift the top of the DVD player too quickly because there are wires attached on the inside.

  • Pry the top of the device open from the right side where the buttons are located.

Agregar Comentario

When pulling the ribbon cables out, make sure not to pull by the wires, as this can cause damage to them. Pinch the plastic adapter with two fingers to remove the wires circled in red from the circuit board. Pinch the plastic adapter with two fingers to remove the wires circled in red from the circuit board.
  • When pulling the ribbon cables out, make sure not to pull by the wires, as this can cause damage to them.

  • Pinch the plastic adapter with two fingers to remove the wires circled in red from the circuit board.

Agregar Comentario

Position the DVD player so that the power and AVI ports are facing you. Pull the white cable with the blue adapters off of the circuit boards. Pull the white cable with the blue adapters off of the circuit boards.
  • Position the DVD player so that the power and AVI ports are facing you.

  • Pull the white cable with the blue adapters off of the circuit boards.

Agregar Comentario

Guía de regalos para el día del padre
Honremos a más que nuestros padres—celebremos a todos los mentores que nos enseñaron a reparar.
Guía de regalos para el día del padre
Honremos a aquellos que nos enseñaron a reparar.
Using the plastic opening tool and your finger, push on the black tab on the inner part of the power port and lift the bottom outer portion of the power port with the plastic opening tool simultaneously. Lift the power port out of the its slot. Lift the power port out of the its slot.
  • Using the plastic opening tool and your finger, push on the black tab on the inner part of the power port and lift the bottom outer portion of the power port with the plastic opening tool simultaneously.

  • Lift the power port out of the its slot.

Agregar Comentario

Remove the four 5mm screws circled in red. Place the blue plastic tool opener underneath the circuitboard and lift up gently. Place the blue plastic tool opener underneath the circuitboard and lift up gently.
  • Remove the four 5mm screws circled in red.

  • Place the blue plastic tool opener underneath the circuitboard and lift up gently.

Agregar Comentario

Unplug the two, 3-pin ribbon cables, which are attached to the circuitboard. For the other circuit board (the one connected to the AVI ports) there are three 6.35mm screws to remove on the outside of the device. For the other circuit board (the one connected to the AVI ports) there are three 6.35mm screws to remove on the outside of the device.
  • Unplug the two, 3-pin ribbon cables, which are attached to the circuitboard.

  • For the other circuit board (the one connected to the AVI ports) there are three 6.35mm screws to remove on the outside of the device.

Agregar Comentario

Remove the four 5mm screws circled in red. Place the plastic opening tool underneath the circuit board, and lift up genttly. As you lift up, slide the circuitboard in a direction away from the AVI ports. Place the plastic opening tool underneath the circuit board, and lift up genttly. As you lift up, slide the circuitboard in a direction away from the AVI ports.
  • Remove the four 5mm screws circled in red.

  • Place the plastic opening tool underneath the circuit board, and lift up genttly. As you lift up, slide the circuitboard in a direction away from the AVI ports.

Agregar Comentario

On the circuit board with the Power Port, de-solder the circled areas on the back to remove the Power port. On the circuit board with the Power Port, de-solder the circled areas on the back to remove the Power port.
  • On the circuit board with the Power Port, de-solder the circled areas on the back to remove the Power port.

Agregar Comentario

On the circuit board with the AVI Port, de-solder the circled areas on the back to remove the AVI Port. On the circuit board with the AVI Port, de-solder the circled areas on the back to remove the AVI Port.
  • On the circuit board with the AVI Port, de-solder the circled areas on the back to remove the AVI Port.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Yufay Chow

Miembro Desde 23/01/12

92 Reputación

4 Guías creadas

Equipo

Cal Poly, Team 10-36, Amido Winter 2012 Miembro de Cal Poly, Team 10-36, Amido Winter 2012

CPSU-AMIDO-W12S10G36

4 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 315