Partes

No se requieren partes.

Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.
  • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the top side.

Agregar Comentario

Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.
  • Using a Phillips #00 screwdriver, remove the four 1.1mm long screws from the bottom side.

  • Remove the warranty sticker across the bottom.

Agregar Comentario

Gently lift off the back and front casing. The outer shell should easily come apart.
  • Gently lift off the back and front casing.

  • The outer shell should easily come apart.

Agregar Comentario

Make sure the device screen is face down.
  • Make sure the device screen is face down.

Agregar Comentario

Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive. Raise the bottom edge of the hard drive 15 degrees up from the device. Raise the bottom edge of the hard drive 15 degrees up from the device.
  • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

  • Raise the bottom edge of the hard drive 15 degrees up from the device.

Agregar Comentario

Kits de Mac RAM
Acelera tu Mac. Maximiza su memoria.
Kits de Mac RAM
Obtén más memoria para tu Mac.
Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module. Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module. Place fingers on the IDE connectors and  gently slide the hard drive out from the   IDE module.
  • Place fingers on the IDE connectors and gently slide the hard drive out from the IDE module.

Agregar Comentario

Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard. Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.
  • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard.

Agregar Comentario

Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.
  • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

Agregar Comentario

Using the plastic opening tool, completely lift the metal bracket off of the motherboard. Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.
  • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

  • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

Agregar Comentario

Using the plastic opening tool, completely lift the ribbon off of the motherboard.
  • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

Agregar Comentario

Completely remove the IDE connector from the device. The audio jack is attached to the IDE connector.  Pull at a 45 degree angle from the audio jack.
  • Completely remove the IDE connector from the device.

  • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

Agregar Comentario

Using the plastic opening tool, wedge the tool underneath the top edge of the motherboard. Completely remove the motherboard.
  • Using the plastic opening tool, wedge the tool underneath the top edge of the motherboard.

  • Completely remove the motherboard.

  • The motherboard should slide out easily.

Agregar Comentario

Locate the plastic screen protector on the front cover.
  • Locate the plastic screen protector on the front cover.

Agregar Comentario

Grasping the sides of the cover, gently press on screen protector from the inside of the front cover to pop out the screen protector.
  • Grasping the sides of the cover, gently press on screen protector from the inside of the front cover to pop out the screen protector.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Una persona más ha completado esta guía.

Ryan Sutardji

Miembro Desde 29/06/12

171 Reputación

7 Guías creadas

Equipo

Cal Poly, Team 1-4, Regan SU 2012 Miembro de Cal Poly, Team 1-4, Regan SU 2012

CPSU-REGAN-SU12S1G4

4 Miembros

7 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 1

Todo El Tiempo: 813