Introducción

You will have to get into the inside of the camera before removing the flash bulb is possible. Some soldering may be required to completely remove the flash unit from the camera.

Unlock the battery cover, while swinging  the cover outward to open it. Unlock the battery cover, while swinging  the cover outward to open it.
  • Unlock the battery cover, while swinging the cover outward to open it.

Agregar Comentario

Turn the camera over and allow the batteries to fall out.
  • Turn the camera over and allow the batteries to fall out.

  • Close the battery cover.

Agregar Comentario

Remove the three 3 mm screws that attach the side panel to the body of the camera. Using your fingernails, pull the side panel outward to remove it. Remove the two remaining 2 mm screws that attach to the frame of the camera.
  • Remove the three 3 mm screws that attach the side panel to the body of the camera.

  • Using your fingernails, pull the side panel outward to remove it.

  • Remove the two remaining 2 mm screws that attach to the frame of the camera.

Agregar Comentario

Remove the 3 mm screw that sits at the bottom of the camera, near the front side.
  • Remove the 3 mm screw that sits at the bottom of the camera, near the front side.

  • Remove the 4 mm screw that sits at the bottom of the camera, near the back side.

Agregar Comentario

Open the battery cover.
  • Open the battery cover.

  • Remove the 5 mm screw that sits on the top of the battery slot.

  • Remove the three 6 mm screws that sit at the bottom of the battery slot.

  • Close the battery cover.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Open the digital A/V DC terminal cover. Remove the three 4 mm screws.
  • Open the digital A/V DC terminal cover.

  • Remove the three 4 mm screws.

  • Detach the digital A/V DC terminal.

  • When you reassemble the camera, leave the topmost screw out until after you put the top casing back.

Agregar Comentario

Grip the sides of the top cover and gently lift the cover until it detaches from the camera.
  • Grip the sides of the top cover and gently lift the cover until it detaches from the camera.

  • Do not completely remove the top cover; an orange ribbon cable still connects it to the camera.

Agregar Comentario

Open the battery cover. With the camera upside down, pull the  front case's side that is closest to you, in an  outward movement.
  • Open the battery cover.

  • With the camera upside down, pull the front case's side that is closest to you, in an outward movement.

  • Apply some force, but pull it gently to prevent damage.

Agregar Comentario

Open the memory card slot cover. Remove the 3 mm screw that sits near the bottom of the case.
  • Open the memory card slot cover.

  • Remove the 3 mm screw that sits near the bottom of the case.

Agregar Comentario

Flip the LCD screen all the way open. Grip both sides of the back case's top and gently pull it, in an outward movement, until the case detaches. Grip both sides of the back case's top and gently pull it, in an outward movement, until the case detaches.
  • Flip the LCD screen all the way open.

  • Grip both sides of the back case's top and gently pull it, in an outward movement, until the case detaches.

Agregar Comentario

Remove the 3 mm screw that holds the flash unit to the camera.
  • Remove the 3 mm screw that holds the flash unit to the camera.

Agregar Comentario

Using your forefinger and thumb, pull the flash unit upward, and out of the camera.
  • Using your forefinger and thumb, pull the flash unit upward, and out of the camera.

  • The flash unit capacitor may cause electric shocks. Do not touch both metallic ends of the capacitor simultaneously.

Agregar Comentario

Remove the 3 mm screw that sits on the back of the circuit board.
  • Remove the 3 mm screw that sits on the back of the circuit board.

Agregar Comentario

Unsolder the white, yellow, brown, and green wires at their soldering points.
  • Unsolder the white, yellow, brown, and green wires at their soldering points.

  • Remove and replace the flash assembly.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Equipo

Cal Poly, Team 11-26, Maness Winter 2011 Miembro de Cal Poly, Team 11-26, Maness Winter 2011

CPSU-MANESS-W11S11G26

3 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 2

Últimos 30 Días: 8

Todo El Tiempo: 4,895