Repara tus cosas Comunidad Tienda

Canon PowerShot SD700 Backlight Replacement

Introducción

Follow these instructions to remove and install a new backlight.

Qué necesitas

  1. Canon PowerShot SD700 Backlight Replacement, Outside Case: paso 1, imagen 1 de 1

    • Turn off the camera by pressing the power button above the LCD screen.

    Traducir

  2. Canon PowerShot SD700 Backlight Replacement: paso 2, imagen 1 de 1

    • Remove the two, small screws on the bottom of the camera using a Phillip's #00 screwdriver.

    Traducir

  3. Canon PowerShot SD700 Backlight Replacement: paso 3, imagen 1 de 1

    • Use a Phillips #00 screwdriver to remove the two, small screws on the right side of the camera.

    Traducir

  4. Canon PowerShot SD700 Backlight Replacement: paso 4, imagen 1 de 1

    • Use a Phillips #00 screwdriver to remove the screw on the left of the camera under the A/V out Digital label.

    Traducir

  6. Canon PowerShot SD700 Backlight Replacement: paso 5, imagen 1 de 1

    • Use a Phillips #00 screwdriver, remove the screw on the bottom of the camera near the battery and memory card slots.

    • This screw will be longer than the rest of the screws.

    Traducir

  7. Canon PowerShot SD700 Backlight Replacement: paso 6, imagen 1 de 1

    • Remove the front, back, and side casings from the camera and set to the side.

    Traducir

  8. Canon PowerShot SD700 Backlight Replacement, LCD screen: paso 7, imagen 1 de 1

    • Remove the two screws that connect the LCD and backlight to the main body of the camera.

    Traducir

  9. Canon PowerShot SD700 Backlight Replacement: paso 8, imagen 1 de 3 Canon PowerShot SD700 Backlight Replacement: paso 8, imagen 2 de 3 Canon PowerShot SD700 Backlight Replacement: paso 8, imagen 3 de 3

    • Gently pry the LCD and the backlight from the main body of the camera.

    • Gently pry the LCD from the backlight.

    • The thin ribbon cable is for the backlight.

    • The thick ribbon cable is for the LCD screen.

    Traducir

  10. Canon PowerShot SD700 Backlight Replacement: paso 9, imagen 1 de 1

    • Carefully lift the ZIF connector that covers the thick ribbon cable.

    • This ZIF connector is fragile. Use caution when lifting it from its down position.

    • Insert the new LCD and reassemble the camera.

    Traducir

  11. Canon PowerShot SD700 Backlight Replacement, Backlight: paso 10, imagen 1 de 1

    • Unplug the ribbon from the housing on the circuitry.

    • Take the new ribbon and insert it into the housing.

    • Tweezers or a tool with a sharp point can be used.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 4 otros colaboradores

Emilio Rossi

Miembro Desde 04/07/11

113 Reputación

3 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

Cal Poly, Team 9-71, Walters Spring 2011 Miembro de Cal Poly, Team 9-71, Walters Spring 2011

CPSU-WALTERS-S11S9G71

4 Miembros

9 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 1,606