Repara tus cosas Comunidad Tienda

Canon PowerShot SD1000 LCD Screen Replacement

Qué necesitas

  1. Canon PowerShot SD1000 LCD Screen Replacement, Back Panel: paso 1, imagen 1 de 2 Canon PowerShot SD1000 LCD Screen Replacement, Back Panel: paso 1, imagen 2 de 2

    • Remove the two 2.9 mm screws from the side panel closest to the camera lens.

    Traducir

  2. Canon PowerShot SD1000 LCD Screen Replacement: paso 2, imagen 1 de 1

    • Remove the two 2.9 mm screws from the camera bottom panel.

    Traducir

  3. Canon PowerShot SD1000 LCD Screen Replacement: paso 3, imagen 1 de 1

    • Remove the two 2.9 mm screws from the side panel farthest from the lens.

    Traducir

  4. Canon PowerShot SD1000 LCD Screen Replacement: paso 4, imagen 1 de 1

    • Pull the back panel away from the camera body, starting at the end with the function buttons.

    Traducir

  6. Canon PowerShot SD1000 LCD Screen Replacement: paso 5, imagen 1 de 1

    • Remove the small cover panel and the attached wrist strap mount.

    Traducir

  7. Canon PowerShot SD1000 LCD Screen Replacement, Front Case: paso 6, imagen 1 de 1

    • Remove the front cover by gently pulling it away from the camera body.

    Traducir

  8. Canon PowerShot SD1000 LCD Screen Replacement: paso 7, imagen 1 de 1

    • Place the front cover, back cover, and wrist strap mount in a safe place until you are ready for reassembly.

    Traducir

  9. Canon PowerShot SD1000 LCD Screen Replacement, LCD Screen: paso 8, imagen 1 de 1

    • Remove the two 2.4 mm screws located at the top of the LCD panel.

    Traducir

  10. Canon PowerShot SD1000 LCD Screen Replacement: paso 9, imagen 1 de 2 Canon PowerShot SD1000 LCD Screen Replacement: paso 9, imagen 2 de 2

    • Pull up the metal frame surrounding the LCD screen starting at the side of the camera.

    Traducir

  11. Canon PowerShot SD1000 LCD Screen Replacement: paso 10, imagen 1 de 1

    • Push the metal frame away from the metal tab using the spudger to detach the frame.

    • Rotate the metal frame upwards.

    • The metal framing should be attached by a metal tab towards the bottom of the camera, near the function buttons.

    Traducir

  12. Canon PowerShot SD1000 LCD Screen Replacement: paso 11, imagen 1 de 2 Canon PowerShot SD1000 LCD Screen Replacement: paso 11, imagen 2 de 2

    • Carefully lift the metal frame from the camera.

    • Remove the black LCD screen, leaving the thin lens pieces in place.

    • BE CAREFUL; both components are attached by an orange connector ribbon and cannot be removed yet.

    Traducir

  13. Canon PowerShot SD1000 LCD Screen Replacement: paso 12, imagen 1 de 3 Canon PowerShot SD1000 LCD Screen Replacement: paso 12, imagen 2 de 3 Canon PowerShot SD1000 LCD Screen Replacement: paso 12, imagen 3 de 3

    • Carefully pull on the orange connector ribbon to disconnect the LCD screen.

    • The LCD screen can be pulled out of the frame before disconnecting its connector ribbon.

    • Tweezers are helpful to disconnect the ribbon.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

2 personas más completaron esta guía.

Autor

con 8 otros colaboradores

Phillip Phung

Miembro Desde 01/19/12

651 Reputación

9 Guías creadas

Insignias: 12

+ 9 más insignias

Equipo

Cal Poly, Team 8-18, Maness Winter 2012 Miembro de Cal Poly, Team 8-18, Maness Winter 2012

CPSU-MANESS-W12S8G18

4 Miembros

12 Guías creadas

Un comentario

Very helpful. These units still sell for a lot more than the cost of the replacement LCD

George Francis - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 10

Ultimos 30 días: 26

Todo El Tiempo: 3,504