We did not have an actual back cover or battery for the phone we were given. Therefore, the first couple of steps will be without pictures.
  • We did not have an actual back cover or battery for the phone we were given. Therefore, the first couple of steps will be without pictures.

  • Hold the phone with the back side facing you.

  • Press down on the silver tab towards the bottom end of the phone.

  • Carefully lift up the back casing to reveal the battery.

Agregar Comentario

Put your finger on the top left corner of the battery and lift the battery up and out of its housing.
  • Put your finger on the top left corner of the battery and lift the battery up and out of its housing.

  • The phone should now look like this.

Agregar Comentario

Remove the two top screws using a T5 Torx screwdriver.
  • Remove the two top screws using a T5 Torx screwdriver.

Agregar Comentario

Use a plastic opening tool to pry the edges of the bottom cover until it snaps loose. The cover will now pull off easily.
  • Use a plastic opening tool to pry the edges of the bottom cover until it snaps loose.

  • The cover will now pull off easily.

Agregar Comentario

Use a plastic opening tool to pry between the front and back cover. Start prying from wherever it is easiest to separate the silver and black plastic of the covers.
  • Use a plastic opening tool to pry between the front and back cover.

  • Start prying from wherever it is easiest to separate the silver and black plastic of the covers.

  • There are 5 securing clips on the front panel to disconnect.

  • Pry gently to prevent breaking the plastic clips when removing the front panel.

  • Once all the clips have been freed, the front cover will lift away from the phone.

Agregar Comentario

Lift the flexible keypad away from the device. It should come off easily.
  • Lift the flexible keypad away from the device. It should come off easily.

Agregar Comentario

Use a T6 Torx Screwdriver to remove the four corner screws on the keyboard's housing. Lift the keyboard frame away from the device.
  • Use a T6 Torx Screwdriver to remove the four corner screws on the keyboard's housing.

  • Lift the keyboard frame away from the device.

  • There may be a small amount of adhesive at the bottom of the frame that needs to be pulled away.

Agregar Comentario

Detach each side casing by pulling them off gently from the phone. Detach each side casing by pulling them off gently from the phone.
  • Detach each side casing by pulling them off gently from the phone.

Agregar Comentario

Remove the back housing from the mother board.
  • Remove the back housing from the mother board.

Agregar Comentario

Unhook the screen frame from the small tab at the top of the motherboard.
  • Unhook the screen frame from the small tab at the top of the motherboard.

Agregar Comentario

Using a plastic opening tool, detach the connector on the LCD screen from the motherboard. There may be some adhesive behind the LCD screen. If needed, pry the LCD screen away from the motherboard using the plastic opening tool.
  • Using a plastic opening tool, detach the connector on the LCD screen from the motherboard.

  • There may be some adhesive behind the LCD screen. If needed, pry the LCD screen away from the motherboard using the plastic opening tool.

  • Remove the LCD screen from the motherboard

Agregar Comentario

Once the LCD screen is taken off, the motherboard is fully separated from the device.
  • Once the LCD screen is taken off, the motherboard is fully separated from the device.

  • The picture shown is the back side of the motherboard.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

Joshua Ramos

Miembro Desde 04/04/12

65 Reputación

2 Guías creadas

Equipo

Cal Poly, Team 14-11, Forte Spring 2012 Miembro de Cal Poly, Team 14-11, Forte Spring 2012

CPSU-FORTE-S12S14G11

5 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 1

Últimos 7 Días: 3

Últimos 30 Días: 9

Todo El Tiempo: 2,119