Introducción

This guide will show you how to replace your broken or defective Digitizer & LCD assembly in your 9500/9530 Storm.

Before ordering your new part, check the number on your existing LCD, it will either be V.014 or V.024, shown in step 11.

Turn your Blackberry Storm 9500 onto its back side, and remove the battery door & battery.
  • Turn your Blackberry Storm 9500 onto its back side, and remove the battery door & battery.

Agregar Comentario

Remove the 2 screws (T6) under the battery compartment they are located as shown in red.
  • Remove the 2 screws (T6) under the battery compartment they are located as shown in red.

Agregar Comentario

Turn the Blackberry Storm 9500 around and pry off the microphone cover at the top using a safe pry tool.
  • Turn the Blackberry Storm 9500 around and pry off the microphone cover at the top using a safe pry tool.

Agregar Comentario

Remove the two screws(T6) as shown.
  • Remove the two screws(T6) as shown.

Agregar Comentario

Flip it back over to the back of the phone, and remove the plastic lens on top of the camera & flash. This is held in place by some adhesive, so use a safe pry tool to remove as shown.
  • Flip it back over to the back of the phone, and remove the plastic lens on top of the camera & flash. This is held in place by some adhesive, so use a safe pry tool to remove as shown.

Agregar Comentario

Once the plastic piece is removed, unscrew the two torx screws underneath it.
  • Once the plastic piece is removed, unscrew the two torx screws underneath it.

Agregar Comentario

Now use a safe pry tool, and go along the edges of the phone to release the clips to open the housing. There are a total of 6 clips, 3 on each side. There is a small cap connection that connects the antenna to the logic board as pictured. There is a small cap connection that connects the antenna to the logic board as pictured.
  • Now use a safe pry tool, and go along the edges of the phone to release the clips to open the housing. There are a total of 6 clips, 3 on each side.

  • There is a small cap connection that connects the antenna to the logic board as pictured.

Agregar Comentario

Once you have worked you way all the way around the device with the safe pry tool you can now separate the two pieces of the housing.
  • Once you have worked you way all the way around the device with the safe pry tool you can now separate the two pieces of the housing.

  • *Be sure to remove the antenna cable in the top portion of the housing. You will need to reattach this when you repair the phone*

Agregar Comentario

Now remove the logic board & LCD assembly from the rear housing. Be gentle, and do not use excessive force.
  • Now remove the logic board & LCD assembly from the rear housing. Be gentle, and do not use excessive force.

Agregar Comentario

Flip the logicboard around so that it is sitting on top of the screen, now remove the two ribbon cables for the LCD & Digitizer. Flip the logicboard around so that it is sitting on top of the screen, now remove the two ribbon cables for the LCD & Digitizer.
  • Flip the logicboard around so that it is sitting on top of the screen, now remove the two ribbon cables for the LCD & Digitizer.

Agregar Comentario

Put your broken assembly to the side, and now install your new one following the past steps in reverse.
  • Put your broken assembly to the side, and now install your new one following the past steps in reverse.

  • Before ordering your new part, check the number on your existing LCD, it will either be V.014 or V.024. (Shown in blue)

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order.

13 personas más completaron esta guía.

Josh Forester

Miembro Desde 28/11/10

2,303 Reputación

10 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 3

Últimos 30 Días: 13

Todo El Tiempo: 20,601