Introducción

Motors can break down, or clog up over time, and need to be replaced or removed for cleaning. This guide will show you how to remove the motor and circuit board.

Grab hold of both the flex hose handle  and the extension wand. Pull straight out to detach the handle from the extension wand.
  • Grab hold of both the flex hose handle and the extension wand.

  • Pull straight out to detach the handle from the extension wand.

Agregar Comentario

Locate the lock clip on the other end of the flex hose.
  • Locate the lock clip on the other end of the flex hose.

- color code this step to match the red indicator

-watch out for the lighting (hard shadows)

Austin Marshall - Contestar

Hold down the lock clip to unlock the flex hose from the vacuum. Remove the flex hose from the vacuum.
  • Hold down the lock clip to unlock the flex hose from the vacuum.

  • Remove the flex hose from the vacuum.

Agregar Comentario

After removing hose, place vacuum on back and unclip the top compartment. Open the compartment. Pull the dirt collection box out of the vacuum.
  • After removing hose, place vacuum on back and unclip the top compartment.

  • Open the compartment.

  • Pull the dirt collection box out of the vacuum.

Agregar Comentario

Place dirt collection box to the side. Locate the Pre-Motor Filter. Pull the filter out by grabbing the pull tab on top.
  • Place dirt collection box to the side.

  • Locate the Pre-Motor Filter.

  • Pull the filter out by grabbing the pull tab on top.

Agregar Comentario

Turn vacuum around and locate the filter cover on the bottom. Place fingers in the opening and pull off the filter cover. Place fingers on each tab on the Post-Motor HEPA Media Filter and pull out.
  • Turn vacuum around and locate the filter cover on the bottom.

  • Place fingers in the opening and pull off the filter cover.

  • Place fingers on each tab on the Post-Motor HEPA Media Filter and pull out.

Agregar Comentario

Take filter out to clean or replace. To clean Dirt Collection Box, unlatch lid and take off. To clean Dirt Collection Box, unlatch lid and take off.
  • Take filter out to clean or replace.

  • To clean Dirt Collection Box, unlatch lid and take off.

Agregar Comentario

Flip Dirt Collection Box over and locate the push tab. Push the Dirt Cup HEPA Media Filter up to take it off. Picture 3 Shows all the filters taken out of the vacuum.
  • Flip Dirt Collection Box over and locate the push tab.

  • Push the Dirt Cup HEPA Media Filter up to take it off.

  • Picture 3 Shows all the filters taken out of the vacuum.

Agregar Comentario

Unscrew the two screws underneath the dirt collection box inside the vacuum. Unscrew the two screws underneath the dirt collection box inside the vacuum.
  • Unscrew the two screws underneath the dirt collection box inside the vacuum.

- color code this step to match the red indicator

Austin Marshall - Contestar

Flip over vacuum.
  • Flip over vacuum.

Agregar Comentario

Unscrew both screws on the bottom of the handle. Unscrew both screws on the bottom of the handle.
  • Unscrew both screws on the bottom of the handle.

- dark lighting (black screw against black medium)

Austin Marshall - Contestar

Unscrew both screws near the wheels. Unscrew both screws near the wheels.
  • Unscrew both screws near the wheels.

- dark lighting (black screw against black medium)

Austin Marshall - Contestar

- missing period

Austin Marshall - Contestar

Flip over vacuum. Gently lift off top. Do not try to take off completely. There are still wires attached to the hull.
  • Flip over vacuum.

  • Gently lift off top.

  • Do not try to take off completely. There are still wires attached to the hull.

- keep extra items out of frame

Austin Marshall - Contestar

- missing period

Austin Marshall - Contestar

Locate the circuit board. Locate the circuit board.
  • Locate the circuit board.

- missing period

Austin Marshall - Contestar

Unplug each orange plug. Make sure you remember which orange plug goes where! Make sure you remember which orange plug goes where!
  • Unplug each orange plug.

  • Make sure you remember which orange plug goes where!

- missing period

Austin Marshall - Contestar

Unplug the red wires. The wires may be a little difficult to take off. If they are, you may use a pair of pliers to pull the wires off. Make sure not to wiggle the wires, as that may break the metal holding them.
  • Unplug the red wires. The wires may be a little difficult to take off. If they are, you may use a pair of pliers to pull the wires off.

  • Make sure not to wiggle the wires, as that may break the metal holding them.

Agregar Comentario

Remove the top.
  • Remove the top.

- missing period

Austin Marshall - Contestar

Unscrew the top two screws on the vacuum. Unscrew the top two screws on the vacuum.
  • Unscrew the top two screws on the vacuum.

- missing period

-add indicator

- hard shadows

Austin Marshall - Contestar

Unscrew the back two scews. Unscrew the back two scews.
  • Unscrew the back two scews.

- blurry image

- hard shadows

-indicators

- black screwdriver against black medium

Austin Marshall - Contestar

Lift motor and move it over the gain access to the spool. Unscrew the screw on the spool. Remove the plastic circle.
  • Lift motor and move it over the gain access to the spool.

  • Unscrew the screw on the spool.

  • Remove the plastic circle.

- missing period

- 2nd picture excess?

Austin Marshall - Contestar

Remove the motor.
  • Remove the motor.

  • And you are done!

- you are not done after completion of this step.

Austin Marshall - Contestar

Conclusión

To reassemble your device, follow these instructions in reverse order.

Mathis Weyrich

Miembro Desde 18/01/18

267 Reputación

1 Guía escrita

Equipo

Cal Poly, Team S12-G1, Banghart Winter 2018 Miembro de Cal Poly, Team S12-G1, Banghart Winter 2018

CPSU-BANGHART-W18S12G1

5 Miembros

5 Guías creadas

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 7

Últimos 30 Días: 12

Todo El Tiempo: 56