Introducción

To repair most parts on the Acer Aspire 1410 apart from HDD, RAM or battery it is necessary to disassemble the entire laptop computer. The motherboard is tricky to get to, and components are soldered on, but with perseverance, it can be done.

With laptop closed, turn screenside down and remove the battery. Unscrew covers and remove HDD. Unscrew cover and remove RAM.
  • With laptop closed, turn screenside down and remove the battery.

  • Unscrew covers and remove HDD.

  • Unscrew cover and remove RAM.

  • Unscrew and remove cover for fan.

Agregar Comentario

Turn laptop so that hinges are closest to you and remove screw from rear of each hinge.
  • Turn laptop so that hinges are closest to you and remove screw from rear of each hinge.

  • Remove screws securing bottom case to logic board. (It won't come off just yet though)

Agregar Comentario

Turn laptop over and open the screen fully. Take care as the screen is still connected to the logic board via black cable on right hinge. Use a spudger to release the silver and black plastic cover that forms the hinge covers. Start at one side nearest a hinge and work along the rear of the case, there are 5 tabs to release along the keyboard edge. Disconnect LCD cable by lifting straight upwards using the black plastic tabs on the top of the LCD connector. You may need to use a spudger to loosen the connection along the uppermost edge-not along the logicboard.
  • Turn laptop over and open the screen fully. Take care as the screen is still connected to the logic board via black cable on right hinge.

  • Use a spudger to release the silver and black plastic cover that forms the hinge covers. Start at one side nearest a hinge and work along the rear of the case, there are 5 tabs to release along the keyboard edge.

  • Disconnect LCD cable by lifting straight upwards using the black plastic tabs on the top of the LCD connector. You may need to use a spudger to loosen the connection along the uppermost edge-not along the logicboard.

  • Remove 2 screws from left and right hinges.

  • Remove 2 screws securing topcase to rear of battery tray.

Agregar Comentario

Remove 2 screws securing power board to logicboard. Lift LCD screen from bottom case. Lift LCD screen from bottom case.
  • Remove 2 screws securing power board to logicboard.

  • Lift LCD screen from bottom case.

Agregar Comentario

Mac RAM Kits
Speed up your Mac. Max out its memory.
Mac RAM Kits
Get more memory out of your Mac.
Remove 2 screws securing the keyboard to case. Use a spudger to release tabs on all 4 sides of the keyboard. Do not pull keyboard up too far as the trackpad and keyboard flex cables are still attached to the logicboard.
  • Remove 2 screws securing the keyboard to case.

  • Use a spudger to release tabs on all 4 sides of the keyboard. Do not pull keyboard up too far as the trackpad and keyboard flex cables are still attached to the logicboard.

  • Place ducks in sink, make sure to disinfect sink afterwards.

Where do I find these ducks at? My computer apparently didn't come with them. I must have the wrong model.

Derek Phillips - Contestar

Do not pull keyboard upwards as it is still attached to logicboard. Flip keyboard over to cover trackpad. Disconnect keyboard. Flip keyboard over to cover trackpad. Disconnect keyboard.
  • Do not pull keyboard upwards as it is still attached to logicboard.

  • Flip keyboard over to cover trackpad. Disconnect keyboard.

Agregar Comentario

Disconnect trackpad. Use a spudger to ease topcase free of bottom case. Slide topcase toward trackpad and then lift up. Resistance can be felt from magnets on topcase. Your laptop should now look like this; middle photo is the remaining logicboard and bottom case, the last photo is the topcase cover.
  • Disconnect trackpad.

  • Use a spudger to ease topcase free of bottom case. Slide topcase toward trackpad and then lift up. Resistance can be felt from magnets on topcase.

  • Your laptop should now look like this; middle photo is the remaining logicboard and bottom case, the last photo is the topcase cover.

Agregar Comentario

Remove logicboard screws. Remove 2 screws securing wifi board. Disconnect wire from wifi board to logicboard.
  • Remove logicboard screws.

  • Remove 2 screws securing wifi board.

  • Disconnect wire from wifi board to logicboard.

  • Disconnect speaker wires form logic board.

Agregar Comentario

Use hex no.5 tool to unscrew 2 bolts from port next ac-in jack.
  • Use hex no.5 tool to unscrew 2 bolts from port next ac-in jack.

Agregar Comentario

Slide DVD drive from logicboard frame. Slide logicboard toward trackpad and then lift out of logicboard frame. The logicboard has a pin connection to the battery tray preventing direct lifting of the logicboard. Last 2 photo's show top of logicboard and underside of logicboard.
  • Slide DVD drive from logicboard frame.

  • Slide logicboard toward trackpad and then lift out of logicboard frame. The logicboard has a pin connection to the battery tray preventing direct lifting of the logicboard.

  • Last 2 photo's show top of logicboard and underside of logicboard.

Agregar Comentario

Conclusión

To reassemble your device, follow these instructions in reverse order. Remember to place logicboard in ac power connection end in first

18 personas más completaron esta guía.

pollytintop

Miembro Desde 09/06/10

73,845 Reputación

10 Guías creadas

Equipo

Master Techs Miembro de Master Techs

Community

276 Miembros

717 Guías creadas

superb thanx thanx thanx

thushararoshanperera - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 3

Últimos 7 Días: 17

Últimos 30 Días: 77

Todo El Tiempo: 13,073