Saltar al contenido principal

Repara tus cosas

Derecho a reparar

Tienda

Aviso: Estás editando una guía de prerrequisito. Cualquier cambio que realices afectará a todas las 8 guías que incluyen este paso.

Inglés
Francés
Paso 7
Insert the edge of an opening tool under the steel mid plate near the bottom left corner of the Touch. Slowly pry upward to separate the plate from the adhesive securing it to the plastic inner case. If the plate is still attached to the logic board, re-warm the area to loosen the adhesive, then slowly separate the plate from the logic board using the opening tool.
  • Insert the edge of an opening tool under the steel mid plate near the bottom left corner of the Touch.

  • Slowly pry upward to separate the plate from the adhesive securing it to the plastic inner case.

  • If the plate is still attached to the logic board, re-warm the area to loosen the adhesive, then slowly separate the plate from the logic board using the opening tool.

  • There is a thin, fragile ribbon cable underneath the plate. As you pry the plate up, be very careful not to rip the cable.

  • This cable may stick to the plate and will tear very easily if you're not careful. Work slowly and be careful not to strain the cable.

Insérez le bord d'un outil d'ouverture pour iPod sous la plaque médiane en acier près du coin inférieur gauche du touch.

Faites leveir vers le haut pour séparer la plaque de l'adhésif la fixant au boîtier intérieur en plastique.

Si la plaque est toujours attachée à la carte mère, réchauffez cette zone pour ramollir l'adhésif, puis séparez la plaque de la carte mère à l'aide de l'outil d'ouverture.

Faites extrêmement attention, le haut-parleur se trouve sous la zone indiquée sur la photo. Il est relié à des fils très fins et courts.

Ici une nappe très mince relie les boutons de volume et de marche à la carte mère. Essayez de contourner cette zone comme sur la photo, afin de ne pas déchirer la nappe. Assurez-vous de maintenir cette nappe enfoncée lorsque vous soulevez la plaque. Elle pourrait coller à la plaque en raison de la colle et est extrêmement fragile.

Cette nappe se déchire très facilement si vous ne faites pas attention.

Il y a également de l'adhésif dans la zone indiquée en rouge.

[* black] Insert the edge of an iPod opening tool under the steel mid plate near the bottom left corner of the Touch.
[* black] PrySlowly pry upward to separate the plate from the adhesive securing it to the plastic inner case.
[* blackred] If the plate is still attached to the logic boardboard, re-warm the area to loosen the adhesive, then slowly separate the plate from the logic board using the opening tool
[* icon_caution] Use extreme care, the speaker is under the area shown in photo. It is connected with very thin and short wires
tool.
[* orange] There is a very thinthin, fragile ribbon cable here that connectsunderneath the volume and power buttons toplate. As you pry the logic board. Try to work around this area like shown soplate up, be very careful not to rip the cable. Be sure to hold down this
[* icon_caution] This
cable when lifting the plate. It couldmay stick to the plate due to residual glue. It is extremely fragile.
[* icon_caution] This cable
and will tear very easily if you areyou're not careful.
[* red] There is also adhesive under
Work slowly and be careful not to strain the area shown in redcable.
[* black] Insert the edge of an iPod opening tool under the steel mid plate near the bottom left corner of the Touch.
[* black] PrySlowly pry upward to separate the plate from the adhesive securing it to the plastic inner case.
[* blackred] If the plate is still attached to the logic boardboard, re-warm the area to loosen the adhesive, then slowly separate the plate from the logic board using the opening tool
[* icon_caution] Use extreme care, the speaker is under the area shown in photo. It is connected with very thin and short wires
tool.
[* orange] There is a very thinthin, fragile ribbon cable here that connectsunderneath the volume and power buttons toplate. As you pry the logic board. Try to work around this area like shown soplate up, be very careful not to rip the cable. Be sure to hold down this
[* icon_caution] This
cable when lifting the plate. It couldmay stick to the plate due to residual glue. It is extremely fragile.
[* icon_caution] This cable
and will tear very easily if you areyou're not careful.
[* red] There is also adhesive under
Work slowly and be careful not to strain the area shown in redcable.

Tus contribuciones son autorizadas bajo la licencia de código abierto de Creative Commons.