Repara tus cosas

Derecho a reparar

Tienda

Aviso: Estás editando una guía de prerrequisito. Cualquier cambio que realices afectará a todas las 2 guías que incluyen este paso.

Volver a la Guía
Inglés
Chino
Paso anterior

Traduciendo paso 14

Paso 14
Follow this guide to reinstall the back cover and replace the adhesive.

  • Follow this guide to reinstall the back cover and replace the adhesive.

  • Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.

  • If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

要重新安装后盖：

首先使用镊子从后盖和手机底盘上剥下任何剩余的粘合剂。

然后，用高浓度异丙醇（至少90％）和无绒布清洁粘合区域。仅向一个方向滑动，而不是来回滑动。这将有助于为新粘合剂制备表面。

在安装新的粘合剂并重新密封手机之前，请务必打开手机并测试维修。

更换粘合剂采用预切片材，以匹配后盖的精确轮廓。如果没有，你可以使用高粘合双面胶带，例如Tesa 61395.请注意，这会留下易受液体侵入影响的间隙。

安装后盖后，对手机施加强劲稳定的压力几分钟，以帮助粘合剂形成良好的粘合，例如将其放在一堆厚重的书本下面。

如果需要，你可以重新安装后盖而无需更换粘合剂。去除任何可能阻止后盖齐平的大块粘合剂。安装后，加热后盖并施加压力以固定后盖。它不会防水，但胶水通常强度足以容纳。

[* icon_reminder] To reinstall the back cover:
[* black] First use tweezers[guide|124003|Follow this guide|new_window=true] to peel away any remaining adhesive from bothreinstall the back cover and replace the phone's chassis.
[* black] Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
[* blackicon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
[* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
[* icon_reminder] To reinstall the back cover:
[* black] First use tweezers[guide|124003|Follow this guide|new_window=true] to peel away any remaining adhesive from bothreinstall the back cover and replace the phone's chassis.
[* black] Then, clean the adhesion areas with high concentration isopropyl alcohol (at least 90%) and a lint-free cloth. Swipe in one direction only, not back and forth. This will help prep the surface for the new adhesive.
[* blackicon_note] Be sure to turn on your phone and test your repair before installing new adhesive and resealing the phone.
[* icon_note] Replacement adhesive comes in a pre-cut sheet to match the exact contours of the back cover. If that's not available, you can use a high-bond double-sided tape, such as [product|IF317-072|Tesa 61395|new_window=true]. Be aware that this leaves gaps that are vulnerable to liquid intrusion.
[* black] After installing the rear cover, apply strong, steady pressure to your phone for several minutes to help the adhesive form a good bond, such as by placing it under a stack of heavy books.
[* icon_note] If desired, you may reinstall the back cover without replacing the adhesive. Remove any large chunks of adhesive that might prevent the back cover from sitting down flush. After installation, heat the back cover and apply pressure to secure it. It won't be waterproof, but the glue is usually more than strong enough to hold.

Tus contribuciones son autorizadas bajo la licencia de código abierto de Creative Commons.