Repara tus cosas

Derecho a reparar

Tienda

the Panasonic Lumix DMC-FX01 Camera Lens Replacement

Escrito Por: Caleb Fink (y 5 de otros participantes)
  • Comentarios: 0
  • Favoritos: 5
  • Terminaciones: 4

Dificultad

Moderado

Pasos

24

Tiempo Requerido

45 minutos - 1 hora

Secciones

5

Banderas

1

Confusing Text

Texto confuso

Parte del texto de esta guía es confuso, duplicado o fuera de tema. Mejorala!

Introducción

The guide takes place from the Camera Lens Assembly guide.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Locate the memory card and battery card latch on the bottom of the camera.

    • Locate the memory card and battery card latch on the bottom of the camera.

    • Slide the latch to the open position.

    Traducir

  2. Open the battery latch, and slide the battery release lever to the right.

    • Open the battery latch, and slide the battery release lever to the right.

    Traducir

  3. Remove the battery from the camera.

    • Remove the battery from the camera.

    Traducir

  4. Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

    • Using a size #00 Phillips screwdriver, remove the three 4.58 mm screws on the bottom of the camera.

    • Use this screwdriver for all screws in the device.

    Traducir

  5. Remove the 3.15 mm screw on the left side of the camera.

    • Remove the 3.15 mm screw on the left side of the camera.

    Traducir

  6. Remove the left side casing. Remove the left side casing.

    • Remove the left side casing.

    Traducir

  7. Remove the two 3.15 mm screws on the right side of the camera.

    • Remove the two 3.15 mm screws on the right side of the camera.

    Traducir

  8. Remove the bottom right panel.

    • Remove the bottom right panel.

    Traducir

  10. Gently remove the back casing. Start at the bottom and carefully pry towards the top to get this piece free.

    • Gently remove the back casing.

    • Start at the bottom and carefully pry towards the top to get this piece free.

    Traducir

  11. Remove the two black 5.35 mm screws that hold in the front faceplate. There may be a third screw the the right of the lens assembly.

    • Remove the two black 5.35 mm screws that hold in the front faceplate.

    • There may be a third screw the the right of the lens assembly.

    Traducir

  12. Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery. Carefully remove the upper assembly, which houses the buttons and the flash battery.

    • Carefully remove the upper assembly, which houses the buttons and the flash battery.

    Traducir

  13. Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

    • Carefully remove the front casing after verifying that the thin plastic around the lens is not still attached.

    Traducir

  14. Remove the three black 5mm screws attached to the lens frame. Remove the three black 5mm screws attached to the lens frame.

    • Remove the three black 5mm screws attached to the lens frame.

    Traducir

  15. Remove the lens frame.

    • Remove the lens frame.

    Traducir

  16. Lift out the circuit board as shown.

    • Lift out the circuit board as shown.

    Traducir

  17. Lift the two black latches that hold the connector ribbons in place. Disconnect the two ribbons.

    • Lift the two black latches that hold the connector ribbons in place.

    • Disconnect the two ribbons.

    Traducir

  18. Remove the lens assembly as shown.

    • Remove the lens assembly as shown.

    Traducir

  19. Remove four 4mm screws from the lens assembly.

    • Remove four 4mm screws from the lens assembly.

    Traducir

  20. Carefully turn over the assembly. Carefully turn over the assembly.

    • Carefully turn over the assembly.

    Traducir

  21. Remove the Fixed Frame Unit by separating it from the assembly. Remove the Direct Frame Unit from the assembly.

    • Remove the Fixed Frame Unit by separating it from the assembly.

    • Remove the Direct Frame Unit from the assembly.

    Traducir

  22. Remove the 1st lens frame from the lens assembly.

    • Remove the 1st lens frame from the lens assembly.

    Traducir

  23. Detach the 2nd Frame Unit from the assembly.

    • Detach the 2nd Frame Unit from the assembly.

    Traducir

  24. Remove the 4mm screw from the lens housing.

    • Remove the 4mm screw from the lens housing.

    Traducir

  25. Separate the lens housing.

    • Separate the lens housing.

    • Replace the lens by gently prying away from the assembly.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

4 personas más completaron esta guía.

Autor

con 5 otros colaboradores

Caleb Fink

Miembro Desde 11/10/10

186 Reputación

2 Guías creadas

Insignias: 8

+ 5 más insignias

Equipo

Cal Poly, Team 9-22, Regan Fall 2010 Miembro de Cal Poly, Team 9-22, Regan Fall 2010

CPSU-REGAN-F10S9G22

4 Miembros

8 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 1

Ultimos 30 días: 5

Todo El Tiempo: 12,129