Repara tus cosas Comunidad Tienda

iRobot Roomba 891 Side Brush Motor Replacement

Introducción

This easy to follow guide will walk you through replacing a defective side brush module on your roomba. This guide requires a propriatery bit screwdriver that is not found in most homes. You will need to purchase one before begining.

Qué necesitas

  1. iRobot Roomba 891 Side Brush Motor Replacement, Battery: paso 1, imagen 1 de 2 iRobot Roomba 891 Side Brush Motor Replacement, Battery: paso 1, imagen 2 de 2

    • Start by flipping your Roomba onto its back on a flat surface.

    • Be sure not to close the side brush bristles in the battery door during reassembly as shown by the handy warning in the second photo.

    Editar

  2. iRobot Roomba 891 Side Brush Motor Replacement: paso 2, imagen 1 de 1

    • Unscrew both the 11mm Phillips #2 screws from the battery cover and remove cover from the Roomba.

    • These captive screws are not intended to be removed from the cover.

    Editar

  3. iRobot Roomba 891 Side Brush Motor Replacement: paso 3, imagen 1 de 3 iRobot Roomba 891 Side Brush Motor Replacement: paso 3, imagen 2 de 3 iRobot Roomba 891 Side Brush Motor Replacement: paso 3, imagen 3 de 3

    • Grasp the tabs on either side of the battery.

    • Remove the battery by pulling up on the tabs.

    • While you're here, check the battery contacts for corrosion or debris.

    Editar

  5. iRobot Roomba 891 Side Brush Motor Replacement, Side Brush: paso 4, imagen 1 de 2 iRobot Roomba 891 Side Brush Motor Replacement, Side Brush: paso 4, imagen 2 de 2

    • Remove the 7.5mm flat head #4 screw from center of the side brush.

    Editar

  6. iRobot Roomba 891 Side Brush Motor Replacement: paso 5, imagen 1 de 1

    • Gently pull the side brush off of the motor hub.

    Editar

  7. iRobot Roomba 891 Side Brush Motor Replacement, Side Brush Motor: paso 6, imagen 1 de 1

    • Remove dustbin from Roomba.

    Editar

  8. iRobot Roomba 891 Side Brush Motor Replacement: paso 7, imagen 1 de 2 iRobot Roomba 891 Side Brush Motor Replacement: paso 7, imagen 2 de 2

    • Unscrew 2 phillips #2 screws from the bottom cover.

    • Remove the bottom cover.

    Editar

  9. iRobot Roomba 891 Side Brush Motor Replacement: paso 8, imagen 1 de 3 iRobot Roomba 891 Side Brush Motor Replacement: paso 8, imagen 2 de 3 iRobot Roomba 891 Side Brush Motor Replacement: paso 8, imagen 3 de 3

    • Unscrew and remove the single 13mm Tri-point Y1 screw and retaining tab.

    • Loosen two captive Phillips #00 16mm screws.

    Editar

  10. iRobot Roomba 891 Side Brush Motor Replacement: paso 9, imagen 1 de 2 iRobot Roomba 891 Side Brush Motor Replacement: paso 9, imagen 2 de 2

    • Grasp motor module and remove from roomba.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

Un comentario

We did this whole process and it still doesn’t turn :0(

jeanne.curnuck - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 5

Todo El Tiempo: 369