Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
La imagen de la izquierda (el panel frontal ya se quitó) muestra las ubicaciones de los clips metálicos (que se muestran en rojo) que se ajustan al marco de plástico. En los siguientes pasos, intenta levantar el panel frontal de los espacios entre estos clips.
-
-
-
Continúa levantando el borde izquierdo hasta que los bordes superior e inferior comiencen a levantarse del Touch.
-
Una vez que los bordes superior e inferior se hayan levantado ligeramente del Touch, usa la herramienta de apertura para asegurarse de que el marco de plástico se separe de los clips a lo largo del interior del Touch.
-
-
-
Inserta la herramienta de apertura del iPod con el borde inclinado hacia la parte inferior de la pantalla de plástico blanco y el protector metálico debajo.
-
Haz palanca a lo largo del borde inferior de la pantalla lo suficiente como para tomarla con los dedos, teniendo cuidado de no doblar la pantalla.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the battery off the adhesive securing it to the metal display tray.
-
Remove the metal display tray and set it aside.
-
Lay the battery flat in the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single Phillips screw securing the gold pressure contact to the logic board.
-
Use a pair of tweezers to lift the Phillips screw out of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three Phillips screws securing the logic board to the rear panel:
-
Two 2.3 mm screws
-
One 1.9 mm screw
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the edge of an iPod opening tool, flip up the control button ribbon cable retaining flap.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully remove the two large pieces of tape securing the ribbon cables to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of an iPod opening tool to peel back the protective rubber grommet to reveal a hidden Phillips screw.
-
Remove the hidden Phillips screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the remaining Phillips screw securing the upper logic board to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully pull the lower logic board away from the lower edge of the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of an iPod opening tool to carefully free the antenna connector cable from the adhesive securing it to the rear case.
-
Use the edge of your iPod opening tool to disconnect the antenna cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully peel the antenna cable off the adhesive securing it to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the small strip of tape securing the antenna socket ribbon cable to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of an iPod opening tool to peel the antenna socket ribbon cable off the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of an iPod opening tool to carefully peel the Wi-Fi ribbon cable off the adhesive securing it to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use an iPod opening tool to pry the black plastic frame under the upper logic board up from the adhesive securing it to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully remove the logic board assembly from the rear panel, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the power/volume controls to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to remove the yellow kapton tape covering the power/volume control ribbon cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two Phillips screws securing the power/volume controls to the rear panel.
-
Lift the power/volume controls out of the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your finger to push the plastic antenna window through the other side of the rear panel.
-
Remove the plastic antenna window from the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the protective rubber grommet from the bottom left hand corner of the rear panel.
-
Cancelar: No complete esta guía.
9 personas más completaron esta guía.