Saltar al contenido principal

Sustitución de la Batería del iPod Touch 1ª Generación

Qué necesitas

  1. Sustitución de la Batería del iPod Touch 1ª Generación, Carcasa: paso 1, imagen 1 de 1
    • Abrir la carcasa es una tarea difícil y potencialmente peligrosa. Se requiere una buena cantidad de fuerza para encajar la herramienta de apertura de plástico entre las costuras de la carcasa. La carcasa puede dañarse si este paso no se realiza correctamente. Asegúrate de no lastimarte mientras abres tu iPod.

    • Inserta la pequeña herramienta de apertura de plástico en la costura entre el panel de plástico de la pantalla y el panel trasero de metal. El borde en ángulo debe apuntar hacia el panel trasero de metal.

    • Sostén la herramienta en su lugar una vez que esté encajada en el interior y los dos paneles estén separados.

    I found the little plastic tools to be useless. I finally got the case apart using jeweler's screwdrivers, guitar picks, and believe it or not, a wood chisel to split the sides of the case open. And believe it or not, I got back together again - not quite as good as new, but good enough.

    I'd REALLY love to know how Apple technicians get this little beast apart without damaging or nicking the case.

    phinegan - Contestar

    Cita de phinegan:

    I'd REALLY love to know how Apple technicians get this little beast apart without damaging or nicking the case.

    Who's betting the actually replace the back with a brand-spanker - if they repair them at all!

    marc draco - Contestar

    They do replace it with a new back, thats why they said that if you have words on the back (engraved) by someone other then apple, your going to lose those but if there done by apple then they'll do it again (when replaceing the battery they say that)

    Cita de marc draco:

    Who's betting the actually replace the back with a brand-spanker - if they repair them at all!

    shadowfox00101 - Contestar

    I replaced my battery in my 1st gen iPod and it still doesn't hold a charge for more then 5 min. Any ideas?

    ae86keidori - Contestar

    Cita de ae86keidori:

    I replaced my battery in my 1st gen iPod and it still doesn't hold a charge for more then 5 min. Any ideas?

    mine has the same problem. My 1st gen iPod touch dropped in water. after that It still works but can't hold a charge for more than 5 mins. I changed the battery and still the same.

    One of my friend give me some advices, I simply clean the whole logic board with some non water alcohol, and it works. It works perfect now. You can have a try.

    Liku - Contestar

    I found a method that worked for me in opening the case. I started at the top, and used a sewing needle. I'm sure a straight pin world work also. Using some padding between the back of the needle and my hand, I worked the point of the needle between the casing and the metal back. Don't push straight into the gap, push on the edge of the gap down toward the back of the iPod. Once you feel the needle slip in, use it as a guide to get your prying tool in there.

    Paul Jones - Contestar

    Hey, I made it, it's open! My opener tool was useless. A swiss army knife and lots of brute force is your friend. My tool broke apart not resisting such force that is necessary.

    http - Contestar

    lol i dropped my iPod this fixedit because it had no back

    elais - Contestar

    Count get past step 1 :( began seperating the back but the metal back sooner bent than the clips letting loose. I heard something chip then the ipod started getting very hot so I think I punctured the battery :( its going to live outside for a while before I throw it out.

    Mike - Contestar

  2. Sustitución de la Batería del iPod Touch 1ª Generación: paso 2, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 2, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 2, imagen 3 de 3
    • Hay siete clips de sujeción entrelazados en cada lado del iPod. La herramienta de apertura de plástico grande se usará para separar el panel frontal de la parte posterior de metal del iPod.

    • Inserta la herramienta de apertura grande en el lado derecho del iPod, con el borde de la herramienta apuntando hacia la parte posterior de metal.

    • Agranda suavemente la grieta existente moviendo la herramienta de apertura grande y moviéndola hacia la derecha.

    • Continúa haciéndolo hasta que el lado derecho del iPod esté suelto.

  3. Sustitución de la Batería del iPod Touch 1ª Generación: paso 3, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 3, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 3, imagen 3 de 3
    • Cambia al otro lado del iPod.

    • Sigue el mismo procedimiento que en el paso anterior para soltar los siete clips que sujetan los paneles en su lugar.

    • Una vez que se separan los paneles de este lado, el panel posterior se puede separar del resto del iPod.

  4. Sustitución de la Batería del iPod Touch 1ª Generación: paso 4, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 4, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 4, imagen 3 de 3
    • Levanta suavemente el panel posterior con los dedos.

    • La parte delantera y trasera del iPod ahora deben estar completamente separadas.

    • La antena dorada (tercera imagen) puede salirse fácilmente de su alojamiento. Asegúrate de que la antena esté bien colocada antes de cerrar el iPod.

  5. Sustitución de la Batería del iPod Touch 1ª Generación, Placa Lógica: paso 5, imagen 1 de 1
    • La batería está pegada a la pantalla del iPod, pero ningún tornillo la mantiene en su lugar.

    • Voltea el iPod 180 grados para que coincida con la orientación de la imagen.

    • Inserta con cuidado el spudger entre la batería y la pantalla. Hay cables de enrutamiento debajo, así que asegúrate de soltar la batería lentamente.

    Could I possibly just cut the battery cables in this step and solder them to the wires on the new battery??

    DUSTmurph - Contestar

    On reassembly before putting the two screws back in, make sure to slide the top part of the board opposite the screws under the small black plastic notch.

    barlowdo - Contestar

    In step five I was very careful with the spudger at getting the battery loose from the LCD screen but now after reassembly I have white bleed through all around three sides of the LCD screen. It shows up easily on light colored screen backgrounds like the Set up screen. It looks like the spudger some how damaged the back side of the LCD screen during disassembly. Is this glue heat sensitive or is there an alternative to using the spudger that a user can suggest?

    barlowdo - Contestar

    Cita de DUSTmurph:

    Could I possibly just cut the battery cables in this step and solder them to the wires on the new battery??

    I am thinking about trying this myself - It seems a lot less labor intensive than desoldering in that very tight location. I guess the big concern is if there is room for insulation on the spliced wires when the unit gets closed up.

    barlowdo - Contestar

    Cita de barlowdo:

    I am thinking about trying this myself - It seems a lot less labor intensive than desoldering in that very tight location. I guess the big concern is if there is room for insulation on the spliced wires when the unit gets closed up.

    I will add that there is really not a lot of wire length to do a splice on and it may be as difficult to do as soldering to the circuit board.

    barlowdo - Contestar

    Yes, even without de-soldering/soldering, one can simply cut the two wires then put a jumper wire on re-installation.

    I agree with DUSTmurph's, comment.

    profeduards - Contestar

    Is there any jumper little enough to fit in it?

    Giovanni Borney - Contestar

    You could cut the cables and solder the new batt's to these, but I'd make sure the total length of the splice is the same to the original. Also use the smallest-diameter heat-shrink tube to insulate so as not to make a bump that prevents the trinket to close properly.

    Aristarco Palacios - Contestar

  6. Sustitución de la Batería del iPod Touch 1ª Generación: paso 6, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 6, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 6, imagen 3 de 3
    • Usa un spudger (o tus uñas) para quitar la antena dorada. La antena se dobla fácilmente, así que asegúrate de no aplicar demasiada presión. Al volver a armar, coloca la antena dorada en su lugar antes de insertar las placas de circuito de la antena.

    • Usa el spudger para quitar el conector del lado izquierdo.

    • Retira dos tornillos Phillips.

    These two screws are short.

    NoH2O - Contestar

    There is a gold spring coil on the side of the board near the left side. BE VERY CAREFUL! It extremely brittle metal and if smashed down, won't connect with the power switch. Once smashed down, attempting to stretch it back out will break it. I found out the hard way and the only way to fix it is to replace the logic board.

    LukeInDC - Contestar

    Are these really Phillips 00 screws? My supposedly 00 screwdriver is way too big. Maybe they are really Phillips 000. The screws in my device were set with blue locktight (grr). I was able to unscrew three of the six with very small straight edge screwdriver but had to sand off the heads of three more with a Dremel tool. This is dangerous. During the process I barely nicked a component near where the antenna cable connects to the logic board. Now I have a new battery and no WiFi.

    anonymous 6952 - Contestar

  7. Sustitución de la Batería del iPod Touch 1ª Generación: paso 7, imagen 1 de 2 Sustitución de la Batería del iPod Touch 1ª Generación: paso 7, imagen 2 de 2
    • La placa de bucle de antena debe levantarse (está pegada). Con cuidado, usa una herramienta de apertura de plástico o un spudger para desalojar la placa de bucle de antena. La placa está conectada a la electrónica de la antena mediante un pequeño cable plano. Este conjunto de dos tablas es muy frágil.

    • Las dos placas de circuito de antena pequeñas ahora se pueden levantar juntas y su cable naranja se puede separar de la pantalla.

  8. Sustitución de la Batería del iPod Touch 1ª Generación: paso 8, imagen 1 de 2 Sustitución de la Batería del iPod Touch 1ª Generación: paso 8, imagen 2 de 2
    • Usa el spudger para quitar la cinta adhesiva negra. Esto revelará los dos tornillos superiores en la imagen.

    • Desatornilla los cuatro tornillos Phillips.

    • Usa un spudger para desconectar el conector negro.

    • Usa un spudger para desconectar el conector negro.

    Left screw is very short. Right screw is long. Top screws same as bottom ones.

    NoH2O - Contestar

    Also, right top one appears bronze/gold colored while left top one is silver, like the bottom ones. Don't know if this is important. (Also, couldn't figure out how to add to previous comment!)

    NoH2O - Contestar

    Actually you can skip all this taking apart sequence - just remove older battery, clean the soldering holes and solder wires back from top. just put some thin plastic film under logic board where the soldering points are while soldering wires in. I replaced god knows how many batteries like this and they all are fine. that way you can replace battery in 5minutes!

    DigiHead - Contestar

    Right, this is what I did. Although it took me more than 5 minutes just to get the case open.

    Madelaine Gogol -

    i reinstalled the lcd and digitizer. only the top works. the bottom of the screen will not respond to touch. help please !!!

    Nemowuner - Contestar

  9. Sustitución de la Batería del iPod Touch 1ª Generación: paso 9, imagen 1 de 2 Sustitución de la Batería del iPod Touch 1ª Generación: paso 9, imagen 2 de 2
    • Usa el spudger para aflojar la placa lógica de varios lados. Se mantiene en su lugar con pegamento y los cuatro tornillos que se quitaron en el paso anterior.

  10. Sustitución de la Batería del iPod Touch 1ª Generación: paso 10, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 10, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 10, imagen 3 de 3
    • Ten cuidado al voltear la placa lógica. El conector para auriculares y el puerto de acoplamiento están conectados a la placa.

    • Levanta suavemente la placa lógica (y los componentes adjuntos) hacia arriba.

    • La porción más pequeña de la placa lógica que reside debajo es muy flexible y frágil. Asegúrate de no tirar del spudger hacia arriba cuando lo uses para separar la tabla pequeña. Usa solo movimientos de lado a lado.

    • Desliza el spudger debajo de la pequeña porción de la placa lógica. La tabla debe aflojarse una vez que el spudger se haya deslizado casi por completo hacia el otro lado.

    When removing the smaller board, while sliding the spudger, I dislodged a white circular plastic disc stuck to the board which is some kind of buffer to the front side button and the board. It's a little sticky, hopefully I'll be able to put it back the right way.

    NoH2O - Contestar

    I've managed to strip a screw. Be careful of that!

    brittanica101 - Contestar

    I believe the white adhesive disc is the contact for power button, so try replacing the same way it came off. The dotted lines on the white should wrap around the edges of circuit board slightly and the board should hold it in place.

    swips - Contestar

    You don't actually need to remove the smaller portion of the logic board to remove the display. Just lift the larger portion up and out of the way, as illustrated.

    Mo Oishi - Contestar

    When I did this, the headphone jack cable sheared completely. The headphone jack was still down and the board flipped up. There was almost no resistance to indicate something was tearing. Luckily, installing a new headphone jack is pretty easy if you have a fine tip soldering iron. But it was a big delay as I had to order the part.

    jonathan - Contestar

    Cita de jonathan:

    When I did this, the headphone jack cable sheared completely. The headphone jack was still down and the board flipped up. There was almost no resistance to indicate something was tearing. Luckily, installing a new headphone jack is pretty easy if you have a fine tip soldering iron. But it was a big delay as I had to order the part.

    Ryan Lacy - Contestar

    Cita de Ryan:

    Do you have any specific info or guide on how to replace the headphone jack? I agreed to help a friend with their iPod and it turns out a new headphone jack is in order. I have never done a repair on an iPod requiring soldering. I think myself and many others would be grateful for a tutorial.

    Ryan Lacy - Contestar

    Cita de Ryan Lacy:

    Do you have any specific info or guide on how to replace the headphone jack? I agreed to help a friend with their iPod and it turns out a new headphone jack is in order. I have never done a repair on an iPod requiring soldering. I think myself and many others would be grateful for a tutorial.

    Well what worked for me was keeping the old connector on the soldered part. The new ribbon has two holes on each solder connecting point. If the ribbon isn't already ripped, go ahead and rip/cut it. Then simply place the new ribbon on top of the existing end with the solder blobs on it. Press down with the heated tip from on top of the solder pads and the heat should be enough to melt the solder beneath. It should flow right up through the holes with the pressure and voila.

    jonathan - Contestar

    Jonathan did you post any photos or a video of your soldering the new headphone jack to the logic board? I did as you did and broke the small ribbon or cable connecting the headphone jack to the logic board. This is my first attempt at repairing an electronic device, and it ended very badly.

    Lucy - Contestar

    I do it without removing the smaller card : it is more safety !!

    Christophe BRETON - Contestar

  11. Sustitución de la Batería del iPod Touch 1ª Generación: paso 11, imagen 1 de 1
    • La placa lógica y la batería ahora se pueden separar completamente del resto del iPod.

  12. Sustitución de la Batería del iPod Touch 1ª Generación, Baterúa: paso 12, imagen 1 de 1
    • Usa la punta de un spudger para quitar el pegamento blanco turbio que cubre los contactos de la batería.

    • Para reducir el riesgo de cortocircuitar el cable rojo de la batería con el protector de metal, primero puedes quitar el pegamento de los cables blanco y negro de la batería. Después de desoldar los cables blanco y negro, retira el pegamento y desuelda el cable rojo.

  13. Sustitución de la Batería del iPod Touch 1ª Generación: paso 13, imagen 1 de 1
    • Ahora estamos listos para comenzar el proceso de soldadura. Necesitarás un soldador, una soldadura y una mecha para desoldar. Deberías poder encontrar estos artículos en un Radio Shack si aún no los tienes.

    • Limpia el soldador derritiendo una pequeña cantidad de soldadura directamente sobre la punta del soldador y luego frota la punta del soldador con una esponja húmeda.

  14. Sustitución de la Batería del iPod Touch 1ª Generación: paso 14, imagen 1 de 1
    • Coloca la mecha desoldadora encima de la bola de soldadura existente.

    • Coloca el soldador encima de la mecha sobre la bola de soldadura existente.

    • Sostén el soldador en su lugar hasta que la soldadura se derrita en la mecha.

    • Repite el mismo procedimiento en los dos conectores restantes.

    • Saca la batería vieja del iPod. Asegúrate de que se haya quitado toda la soldadura antes de sacar los cables de la placa. Los cables deben salir libres con poca o ninguna resistencia.

  15. Sustitución de la Batería del iPod Touch 1ª Generación: paso 15, imagen 1 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 15, imagen 2 de 3 Sustitución de la Batería del iPod Touch 1ª Generación: paso 15, imagen 3 de 3
    • Recomendamos que limpies la superficie expuesta de la placa con un paño suave o una esponja y una pequeña cantidad de alcohol isopropílico.

    • Derrite una pequeña gota de soldadura directamente sobre el conector metálico de la placa colocando el soldador sobre el conector metálico y luego presionando la soldadura contra la punta del soldador y la placa.

    • Una vez que una pequeña cantidad de soldadura se haya derretido en la placa, levanta primero la soldadura y luego el soldador.

    • El cordón de soldadura debe verse como un pequeño domo o hemisferio. Si es plana o dentada, simplemente coloca el soldador nuevamente sobre la soldadura para volver a fundirla y luego retira el soldador. Puede ser necesaria un poco más de soldadura si lo anterior no funciona.

    I would remove all the solder and use a pin to clear the holes before inserting the cables and resoldering.

    Also get a 'helping hand' - they are a few quid on eBay - similar to this: http://www.laventure.net/tourist/cables3...

    Neil - Contestar

    I removed all the solder as Neil suggests. But to pull the solder out with the wick you may need to add some a little solder to the top of the hole first so that you get good thermal conductivity between the wick and the solder you are trying to remove from the small hole.

    anonymous 6952 - Contestar

  16. Sustitución de la Batería del iPod Touch 1ª Generación: paso 16, imagen 1 de 1
    • Conecta primero la mina negra, luego la roja y termine con la mina blanca.

    • Coloca el cable de la batería nueva en el cordón de soldadura nuevo.

    • Presiona la punta del soldador sobre el cordón de soldadura hasta que se derrita.

    • Desliza el cable conductor en la soldadura líquida hasta que el cable pase por el centro del cordón, luego retira el soldador.

    • Continúa con las otras dos conexiones de la misma manera, teniendo especial cuidado de no soldar dos de los conectores entre sí.

    Don't bead first. The beads are so small and will harden before you can stick the wire in. I put the wires barely through the connection holes and then soldered it.

    Coleen - Contestar

  17. Sustitución de la Batería del iPod Touch 1ª Generación: paso 17, imagen 1 de 1
    • Los cables deben verse muy similares a esta imagen una vez que hayas terminado de soldar.

    Hey guys, I have a question, I have an Ipod touch 1st gen but it needs a battery and the replacements are too expensive so I think to just use brand new nokia 3 contact battery but I don't know what pins are on the ipod and I can't find chematic anywere, do anyone know.

    Rokas Karinauskis - Contestar

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

130 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Francisco Javier Saiz Esteban nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

8 comentarios

When i did this i found the desoldiering wick un necessary. A helper is mutch advised, she held it, i heated and pulled out the old wires, then reused the soldier already there

Dans iPod Repair - Contestar

If you don't want to go to all the trouble and risk of breaking something. Don't take everything apart. Just cut the battery wires as close as possible to the old battery terminals and splice the wires from the new battery on them. A little solder and a bit of electrical tape and your done! It's miller time!

Antoine Habel - Contestar

while this might be an easy way to get the job done, it is for lack of a better word half-assed. It opens the door for shorts and part malfunction in the future. While i can see where you are coming from, it is not the corect way. Do it right the first time.

Dans iPod Repair -

I just replaced my battery. steps from 6 on are useless. All you have to do is desolder the old battery, take it out, then put the new one in and solder it. i did that and it works fine.

saxm93 - Contestar

I stopped at step 5, cut the battery wires and spliced them to those on the new battery and then scotch taped them. It worked, although to official method is doubtless better.

I recommend examining the metal case fastening carefully to see that prongs are flattened before reassembly. Several of mine were bent out and up.

m w - Contestar

I took it apart and stopped before step 6. Took it to an experienced radio repairs man. I think he did a good work soldering three point for £5 but I forgot to check the headphone jack before taking it back home and 'of course' the jack is not working any more. I've did everything I could find on internet to make the jack work again but no.

I doubt it could have broken in the repair but who knows...

Anyway I've ordered a spare jack from Amazon for £5 and I'm thinking of changing it myself.

Unfortunately though the ipod has given up totally on me now. I can't even make it wake/start up connected to iTunes. Oh, dear! my good old friend, won't you please come back to me?!

tronque - Contestar

Any update on whether it's necessary to remove the whole logic board or not?

Would consider myself a novice (getting into self repairs)

Pet - Contestar

Bonjour,

le liens propose une batterie chez Amazon est 1600 mAh, est-ce que l’appareil peut supporté cette intensité ?

MALEK BENCHADI - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 11

Ultimos 7 días: 80

Ultimos 30 días: 426

Todo El Tiempo: 289,924