Saltar al contenido principal

Reemplazo del panel frontal del iPod 3ª Generación

Qué necesitas

  1. Reemplazo del panel frontal del iPod 3ª Generación, Carcasa: paso 1, imagen 1 de 1
    • Antes de abrir su iPod, asegúrate de que el interruptor de retención esté en la posición de bloqueo. La barra naranja debe estar visible, lo que indica que la retención está activa.

    Note that the lock will move out of position again easily once you have the case open (when disengaged from the internal switch). That being said, you will want to keep this little switch in mind even beyond making sure the lock is in the right place, as the little plastic tab that is the switch is extremely small and fragile. I ended up breaking mine off somehow while trying to get the case closed. It is small enough that I never felt it break; I finally got the iPod back together and found that the lock switch didn’t work. I was able to re-open it and use a pick tool to unlock what was left of the switch, so my iPod works, but no longer locks. I’m happy to have a working battery anyhow, but I’d have been happier yet to have completed the repair without breaking anything - be careful with this little switch.

    Joe Sutton - Contestar

  2. Reemplazo del panel frontal del iPod 3ª Generación: paso 2, imagen 1 de 3 Reemplazo del panel frontal del iPod 3ª Generación: paso 2, imagen 2 de 3 Reemplazo del panel frontal del iPod 3ª Generación: paso 2, imagen 3 de 3
    • Inserta una púa de apertura lo más lejos posible en la costura entre el frente de plástico y el panel trasero de metal, en el borde derecho del iPod.

    • Es posible que debas mover la púa hacia adelante y hacia atrás para deslizarla más adentro.

    • Usa la púa de apertura para hacer palanca contra el panel frontal de plástico y suelta las cinco pestañas de retención (que se ven en la tercera foto).

    • Desliza la púa a lo largo del borde del iPod y continúa haciendo palanca para liberar el resto de las pestañas de retención.

    • Una vez que las cinco pestañas del lado derecho estén libres, la carcasa debería abrirse con facilidad.

    Is that wide opening pick shown in the photo available? Or should I be able to get my iPod 3G open with just the narrow opening tool? So far I’ve been unsuccessful.

    David Troup - Contestar

    Hi David, an opening tool can definitely work, but we’ve found that the opening picks tend to be a bit easier. You can find those in our store. The clips are definitely really tough and, like Matthew mentioned, using multiple picks might help. Getting the pick in the seam is the hardest part, then once it’s in you should be able to work it in farther, or add another pick to eventually release the clips.

    Adam O'Camb -

    I had to use about 10 guitar picks. The case “clips” are amazingly tight. I’d get one in just barely, then I’d add another in the now-opened slot. Then another. I’d space them about 1 or 1.5cm apart on two sides. Work into a corner and it will release. (I’m going on memory. I bought packs of the cheapest guitar picks. I have both thin and medium. I think I used medium, but I can’t remember.)

    Matthew Robbins - Contestar

    so much easier to open with an xacto blade and handle. the blade has a more defined edge that helps to move the plastic front cover. then a pick can help do the rest.only took 2 mins. using xacto blade and handle

    dennis fowler - Contestar

    also not mentioned is reattachment of hard drive plug to board . not a normal plug as the others.need to be sure it is attached before closing up ipod. replacement battery was thicker than origional and allowed hd to not sit level

    dennis fowler - Contestar

    I had success holding the iPod im my hand, pushing the plastic with the thumb while pushing on the metal body from the other side. This opened a gap between the parts, where I could insert the pick.

    Jakob - Contestar

    After trying fruitlessly with a variety of plastic tools, I remembered I owned an iSesamo. Got in in 20 seconds.

    Alison Scott - Contestar

    I second the idea of using an Exacto handle with a flat chisel blade to start the opening on the right side. Then I could insert the pick and work it around to undo all the clips. I could get a lot more purchase on the edge and make a gap for the pick. It took some pressure as it’s been 20 years since this unit was built, an iPod Special U2 black edition.

    David Wilcox - Contestar

    As others noted, it’s darn near impossible to get a pick into the seam to get started opening the case. I finally got mine by pressing up on the back of the case, which causes the side of the back piece to angle out a bit and allowed me to get the pick that came with the replacement battery in. Once I finally got that far, it was fairly easy to slide the pick up and down the side of the case to pop free each of the clips. I scubbed up the edge of mine a bit before I figured this out, and those efforts didn’t help, so maybe avoid that. (I didn’t have an Exacto like others have suggested, but having done this, I can see how that might work well also, if you are careful about it)

    Joe Sutton - Contestar

    This tool worked great! iFixit Opening Tool

    I could push the plastic top part back enough to get the pick in.

    Brenna Rentmeester - Contestar

    Two guitar picks did the trick – as soon as the edge of the first pick goes into the gap, twist it more upright; the next pick can then be slid into the opening and the rest of the case opens up easily. One warning: be very careful near the charging port – there’s a delicate plastic trim around the opening in the metal case and I accidentally cut through the trim with the edge of a pick. The trim is attached to the case with two screws so I removed it before repairing it with superglue. This worked well and the trim screwed back in very easily.

    Ian - Contestar

    Get the plectrum in at the charging port where the metal is thinnest, then move left/right and around the first corner, keeping it tightly in the seam. Once around the corner, it begins to ‘pop’ open. Do the same for the other corner and it will open right up.

    Matt - Contestar

    Turn the iPod upside down and squeeze (push the white plastic in while squeezing). You will hear a click, creating a gap to insert the pick. You're welcome. :)

    https://youtu.be/w2DzkFrBEGw

    TONIA PROUTY - Contestar

  3. Reemplazo del panel frontal del iPod 3ª Generación: paso 3, imagen 1 de 1
    • La funda del iPod ahora está abierta, pero todavía no separes las dos mitades. Todavía hay un cable plano naranja que conecta el conector de los auriculares a la placa lógica.

    • Abre la carcasa como un libro con el conector de la base en la parte superior y coloca el panel posterior junto a la mitad frontal del iPod.

    Remember to fold the backplate up the correct direction, otherwise you might break this cable.

    iTronics Repair - Contestar

  4. Reemplazo del panel frontal del iPod 3ª Generación: paso 4, imagen 1 de 2 Reemplazo del panel frontal del iPod 3ª Generación: paso 4, imagen 2 de 2
    • Utiliza una herramienta de plástico o las uñas para desconectar con cuidado el cable naranja del conector de auriculares. Asegúrate de tirar hacia arriba del conector, no del cable en sí.

    • El conector jack de auriculares es inusualmente alto. Al hacer palanca, ten cuidado de no separar la parte inferior de plástico del conector del cable plano. Haz palanca entre el conector y el zócalo, no entre las dos mitades del conector.

    Be more than careful with the headphone jack, because I thought I was until I broke mine (I still don't figure how I did this). Those are hard to find after and if you do, it may cost you something around 20-30$

    Tristan Gauvreau - Contestar

    Yeah, I just did the same. Oops.

    Alex Robinson -

    Yikes - yes, be SUPER careful - just damaged mine too (snapped some of the soldered connections between ribbon and plug). I only use my iPod with a dock in my car, so hoping I will get away with this.

    Russell Coleridge - Contestar

    Arrgh...I should have paid closer attention the red warnings above. I ended up pushing up on the ribbon part rather than the actual socket. Thereby completing separating the connector from the ribbon cable. I got way too excited when I finally got the case loose after an hour of trying that I rushed through this part. Now I have to see if I can replace this part.

    Eric Schenkel - Contestar

    Blech - despite these thoughtful warnings I snapped that plug right off the ribbon! So please, be careful. I found a replacement headphone jack (used) on eBay for 20 bucks. What a not-fun way to spend 20 bucks!

    Matt Michael - Contestar

    Yep - did the same. Bugger. Is it possible to carefully fix? Solder or glue or are there replacement parts? I do actually have another iPod but I was hoping to end up with two working versions rather than one just for parts.

    Greg J Mason - Contestar

    Well, that reminds me to view the comments first before attempting any of the repair steps. Did the same thing. iFixit should put that suggestion at the top of every repair guide. “Review Comments First, Save $20”.

    John Lillywhite - Contestar

    Yep, that’s me buggered too.

    Alistair Hay - Contestar

    Same thing happened to me. I was extra careful. Now what?

    Clayton Adams - Contestar

    I don’t think it’s repairable. I bought one for $20-30 off ebay and cannibalized the ribbon cable.

    kb9rhe - Contestar

    This step appears to be optional for a battery replacement - or, at least, I could not persuade the connector off the logic board without applying more force than I was prepared to given all these warnings. So I just carried on, and replaced the battery without ever removing the headphone jack connector.

    Alison Scott - Contestar

    You are correct, this step is not necessary for a battery replacement although it may give you more room to work with. In my opinion it’s not worth the risk of damaging the connector though, as you can just place the metal cover to the side like Rob said, leaving the connector attached and carefully folding the metal cover to the side like opening a book (although it may not lay perfectly parallel to the front case of the iPod).

    Bagel -

    Yep, the step should be place the metal back cover to the side without removing the connector, because you’re certain to break it, especially if this is the third time you’ve replaced the battery and you forgot to be careful the third time.

    Rob - Contestar

  5. Reemplazo del panel frontal del iPod 3ª Generación, Placa Lógica: paso 5, imagen 1 de 1
    • Levanta el disco duro con una mano y desconecta con cuidado la cinta del disco duro de la placa lógica.

    • Saca el disco duro del iPod.

  6. Reemplazo del panel frontal del iPod 3ª Generación: paso 6, imagen 1 de 1
    • Desconecta con cuidado el conector blanco de la batería de la placa lógica. Asegúrate de tirar solo del conector y no de los cables.

    When putting the iPod back together, be careful the battery wires are inside of the tab. If they are outside of the tab the would get pinched between the case and the tab and likely damaged.

    Yishai Sered - Contestar

  7. Reemplazo del panel frontal del iPod 3ª Generación: paso 7, imagen 1 de 1
    • Usa un spudger para desconectar con cuidado el cable naranja de la rueda táctil de la placa lógica.

  8. Reemplazo del panel frontal del iPod 3ª Generación: paso 8, imagen 1 de 1
    • Retira los 6 tornillos Torx T6 negros que sujetan la placa lógica al panel frontal.

  9. Reemplazo del panel frontal del iPod 3ª Generación: paso 9, imagen 1 de 1
    • Levanta la placa lógica del iPod.

    • Al volver a montar tu iPod, asegúrate de que el mecanismo del interruptor de retención de plástico esté sincronizado con el interruptor de retención de la placa lógica. El interruptor en el tablero es una pequeña protuberancia negra que se encuentra en una ranura en el mecanismo del interruptor de retención.

  10. Reemplazo del panel frontal del iPod 3ª Generación, Pantalla: paso 10, imagen 1 de 1
    • Usa un spudger para desconectar con cuidado la cinta naranja de la pantalla del panel frontal.

    Be very careful with this step. Granted they are old and fragile, but I still managed to break-off the soldering points on the first screen I tried to dislodge.

    VirtualNsanity3 - Contestar

  11. Reemplazo del panel frontal del iPod 3ª Generación: paso 11, imagen 1 de 1
    • Levanta el panel de la pantalla del iPod.

  12. Reemplazo del panel frontal del iPod 3ª Generación, Panel Frontal: paso 12, imagen 1 de 1
    • Saca la batería del iPod.

  13. Reemplazo del panel frontal del iPod 3ª Generación: paso 13, imagen 1 de 1
    • Usa un spudger para desconectar con cuidado la cinta naranja de la pantalla del panel frontal.

  14. Reemplazo del panel frontal del iPod 3ª Generación: paso 14, imagen 1 de 1
    • Queda el panel frontal.

Conclusión

Para volver a armar tu dispositivo, sigue estas instrucciones en orden inverso.

10 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

iRobot

Miembro Desde 09/24/09

1 Reputación

636 Guías creadas

Un comentario

I have a new front housing without the click wheel board. How do I remove the board from the front panel and then re-attatch to the new front housing. Is it glued and what type of glue for the re-install. Do I have to use a rework station heat blower to soften the old glue, and if so what temperature do you recommend?

Thanks

Christopher South - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 7

Ultimos 30 días: 29

Todo El Tiempo: 12,819