Reemplazo de ensamblaje de altavoz del iPhone 7

Introducción

Prerequisito para remover el altavoz o la antena de diversidad inalámbrica.

Qué necesitas

Paso 1 Ensamblaje de altavoz

Reemplazo de ensamblaje de altavoz del iPhone 7, Ensamblaje de altavoz: paso 1, imagen 1 de 1

Remueve el tornillo Phillips que sujeta la antena de diversidad inalámbrica a la caja trasera:
Un tornillo de 3.2 mm.

Traducir

Paso 2

Remueve los siguientes tres tornillos Phillips que sujetan el altavoz a la caja trasera:
Dos tornillos de 1.3 mm
Un tornillo de 2.0 mm

Traducir

Paso 3

Reemplazo de ensamblaje de altavoz del iPhone 7: paso 3, imagen 3 de 3

Usa la punta de un spudger para levantar los dos conectores de antena de los zócalos en la placa lógica.

Traducir

Hey may i ask…what is the use of both of the antenna cables?i just opened my iphone 7 plus and i found both of the cables are broken.if both of the cables are broken,what does it effect on my iphone?

Mohd Wazirul - 8 de ene. de 2018 Contestar

Speaker and antenna?

Keah Smith - 13 de ago. de 2019 Contestar

I'm missing the black thing from my antenna and I have no signal, could this be the reason why? Is the black thing insulation?

Keah Smith - 13 de ago. de 2019 Contestar

These doodads are a pain to route and reconnect. I probably spent 15 minutes just on this part of reassembly. One of them is connected to the new part. It won’t have the soft grommet on top.

Ray Bieze - 18 de nov. de 2019 Contestar

One of these came away from its base. The one nearest the battery.

When I reassemble it I’m thinking just a bit of glue at the side once re attached to base, so lomg as it touches the base contacts?

Any comments?

ANDREW - 29 de ene. de 2020 Contestar

I am having the worst time imaginable trying to reconnect the antenna cable coming from the lightening connector assembly to the logic board. It’s barely long enough and will not snap into place. There’s a minature gold pin sticking up from a circular gold ring on the logic board and I must have spent an hour on this one step. The antenna end has the female end. Everything else went well. The antenna connector from the old lightening assembly will connect relatively quickly. I’m beginning to think the new antenna connector female end might be defective. I’m ready to cut the black antenna wire and try to solder in a longer piece using the old connector assembly. Any ideas? HELP !!!

David Sandrof - 9 de sep. de 2020 Contestar

These can be tricky to reconnect. I found the best way is to hold the connector with tweezers and use the point of a spudger on top of the connector in the other hand. Slowly moving the connector with the tweezers while applying gentle pressure with the spudger, you will eventually feel the connector and its seat line up and you can snap into place. Don’t force it, when it is lined up it is easy so you have to patiently work on aligning it.

David Ege - 5 de dic. de 2020 Contestar

please say which antenna is which, impossible to know now

Mitchell Thompson - 28 de jul. de 2021 Contestar

Tip that helped me: remove the standoff screw next to the clip before derouting (or, upon reassembly, rerouting) the cables. This gives you a lot more space to work with! (Note: I only did this on reassembly, so I don’t know if there are any gotchas on disassembly.)

T Murrills - 1 de dic. de 2021 Contestar

Please pay close attention to witch one goes where or take a picture bad mistake made.

michael - 5 de ene. de 2022 Contestar

Paso 4

Usa pinzas para desviar los cables de antena de su soporte en la placa lógica.

Traducir

Paso 5

Usa pinzas para remover los cables de antena del clip en el altavoz.
Asegúrate de tomar el cable cerca del clip para evitar dañar el cable.

Traducir

They pull off to the side.

Ark - 27 de dic. de 2018 Contestar

This was an oddly challenging step, lifting the speaker slightly from the top end allowed me to slide the tips of one side of the tweezers in between the cable and the speaker, prying it out rather than grabbing and pulling which feels dangerous.

Jesse de Vries - 21 de may. de 2020

They break very easily

Josh Brito - 20 de dic. de 2019 Contestar

difficile a retirer. Les 2 tables sont clipsés sur le haut parleur. Il m’a bien fallu 10 - 15 minutes pour arriver a les retirer. Aucune astuce a vous donner, a part de la persévérance.

Guigui - 27 de abr. de 2020 Contestar

One cable seems to stay attached to the speaker. Don’t try to pry it off the speaker! This is shown in the video but not in these photos.

Cynthia Lamb - 1 de mar. de 2021 Contestar

Paso 6

Usa la punta de un spudger para deslizar el ensamblaje de altavoz hacia la placa lógica y fuera de la caja trasera.

Traducir

Paso 7

Remueve el altavoz.

Traducir

Reassembly tip: after aligning the speaker with the bottom edge, instead of lowering the speaker into place, keep the speaker raised slightly and push the cables back into the clip (which were removed in step 28) with the flat end of a spudger. In doing so, though, make sure that the cable from the lightning connector piece remains above the flat metal piece protruding out the left side of the speaker.

T Murrills - 1 de dic. de 2021 Contestar