Repara tus cosas Comunidad Tienda

iPhone 7 Power and Volume Control Cable Battery Replacement

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Introducción

prereq only

Qué necesitas

  1. iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: paso 1, imagen 1 de 2 iPhone 7 Power and Volume Control Cable Battery Replacement, Power and Volume Control Cable Battery: paso 1, imagen 2 de 2

    • Use the flat end of a spudger to disconnect the Taptic Engine connector from its socket on the logic board.

    Traducir

  2. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 2, imagen 1 de 1

    • Remove the three 1.6 mm Phillips screws securing the Taptic Engine to the rear case.

    Traducir

  3. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 3, imagen 1 de 2 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 3, imagen 2 de 2

    • Remove the Taptic Engine.

    Traducir

  5. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 4, imagen 1 de 3 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 4, imagen 2 de 3 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 4, imagen 3 de 3

    • Use a pair of tweezers with blunt tips to peel back one of the adhesive strips on the lower edge of the battery.

    Traducir

  6. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 5, imagen 1 de 2 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 5, imagen 2 de 2

    • Use a pair of tweezers with blunt tips to peel back the other adhesive strip on the lower edge of the battery.

    Traducir

  7. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 6, imagen 1 de 3 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 6, imagen 2 de 3 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 6, imagen 3 de 3

    • Try to keep the strips flat and unwrinkled during this procedure; wrinkled strips will stick together and break instead of pulling out cleanly.

    • Slowly pull one battery adhesive tab away from the battery, toward the bottom of the iPhone.

    • Pull steadily, maintaining constant tension on the strip until it slips out from between the battery and the rear case. For best results, pull the strip at a 60º angle or less.

    • The strip will stretch to many times its original length. Continue pulling and re-grab the strip near the battery if necessary.

    Traducir

  8. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 7, imagen 1 de 1

    • Repeat the previous step for the second strip.

    • Hold down the battery as you remove the second strip, or the strip may fling the battery when it separates from the case.

    • If you removed both adhesive strips successfully, skip the next step.

    • Otherwise, if either of the adhesive strips broke off underneath the battery and could not be retrieved, continue with the next step below.

    Traducir

  9. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 8, imagen 1 de 2 iPhone 7 Power and Volume Control Cable Battery Replacement: paso 8, imagen 2 de 2

    • If you successfully removed both adhesive strips, move on to the next step. Otherwise, you will need to pry the battery from the rear case.

    • Prepare an iOpener and apply it to the back of the rear case, directly over the battery. Alternatively, you can apply heat using a heat gun or hair dryer.

    • After about a minute, remove the iOpener, flip the phone over and use a plastic card to break up any remaining adhesive behind the battery.

    • Avoid bending the battery. Damage to the battery may release dangerous chemicals, and could start a fire.

    • Do not pry under the top third of the battery, you may damage the volume button ribbon cable.

    Traducir

  10. iPhone 7 Power and Volume Control Cable Battery Replacement: paso 9, imagen 1 de 1

    • Remove the battery.

    • When installing the battery, refer to this guide to replace your battery's adhesive strips.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 3 otros colaboradores

Scott Havard

Miembro Desde 06/27/16

49,633 Reputación

31 Guías creadas

Insignias: 38

+ 35 más insignias

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 136