Saltar al contenido principal

Reemplazo del cable de cinta del botón de inicio del iPhone 5c

Qué necesitas

  1. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Usa cinta adhesiva sobre la pantalla: paso 1, imagen 1 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Usa cinta adhesiva sobre la pantalla: paso 1, imagen 2 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Usa cinta adhesiva sobre la pantalla: paso 1, imagen 3 de 3
    • Si tu pantalla está rota, evita que hayan más desperfectos o que sufras algún accidente con las piezas rotas colocando cinta adhesiva sobre el cristal de la pantalla.

    • Coloca varias capas de cinta adhesiva transparente sobre la pantalla del iPhone hasta cubrirla completamente.

    • Esto hará que los trozos de cristal no se desprendan y proporcionará integridad estructural mientras abres y levantas la pantalla.

    • Usa gafas de seguridad para proteger tus ojos de cualquier fragmento de esquina que pueda desprenderse durante la reparación.

  2. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Quitar los tornillos pentalobulares: paso 2, imagen 1 de 1
    • Antes de continuar, descarga la batería de tu iPhone por debajo del 25%. Una batería de ion de litio puede arder y/o explotar si se perfora accidentalmente.

    • Apaga tu iPhone antes de empezar a desarmarlo.

    • Separa los dos tornillos Pentalobe P2 de 3.8 mm en ambos lados del conector Lightning.

    to keep screws in order, buy some double sided tape and then affix the tape in small pieces to a sheet of paper. As you take the screws out, you can affix them to the tape (which is on the paper) and then write a description of what they are and where they go. quick, cheap and easy.

    V. Jones - Contestar

    I found that these screws did not remove easily. After turning several times and feeling the threads drop back, indicating they were loose, the heads did not extend far enough to grip with my fingernails to pull out. I had to use the tweezers and then it took a bit more force than expected to remove them.

    Jim Thomas - Contestar

    My iPhone 5c has P1 Pentalobe screws, not P2. This guide caused me to buy wrong tools so I thought I would share my experience. Perhaps they vary.

    Cody Craven - Contestar

    @codycraven01 These guides are created using iFixit tools, and P2 is definitely the correct driver. If you’re using tools you bought somewhere else, then yes, results may vary.

    Jeff Suovanen -

  3. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Comenzar la apertura usando un iSclack: paso 3, imagen 1 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Comenzar la apertura usando un iSclack: paso 3, imagen 2 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Comenzar la apertura usando un iSclack: paso 3, imagen 3 de 3
    • Los siguientes dos pasos te mostrarán cómo se usa el iSclack, una gran herramienta para abrir de manera segura el iPhone 5c y que recomendamos a cualquiera que quiera reparar más de una vez un iPhone 5, 5s o 5c. Si no vas a usar el iSclack, ve directamente al Paso 5.

    • Cierra el agarre del iSclack, abriendo las mandíbulas succionadoras.

    • Coloca la parte inferior de tu iPhone entre las ventosas, apoyándolo en el tope de plástico.

    • La ventosa superior debería estar colocado un poco por encima del botón de Inicio.

    • Abre las palancas para que las mandíbulas del iSclack se cierren. Centra las ventosas y presiónalas firmemente sobre la parte de arriba y de abajo del iPhone.

    I just replaced my iPhone 5C battery today and only used the I fix it repair kit that came with the suction cup. Getting the glass screen out was not too difficult as I used a little bit of upward motion on the suction cup while at the same time prying gently with the flat end of the opening tool at the same time. If you have two people it makes it a little easier as someone can hold the phone. After getting the end open, I was able to go around the perimeter and gently pry up the edges with very little trouble.

    V. Jones - Contestar

    Experienced immediate problem: there is s strap going from the home button to the screen, about 1-1/2 inch long. After removing 3-4 screws I saw no way to disconnect it from either end. My daughter came to help get the screws back (my 70 years have problems with very tiny screws). Slid a piece back and the strap came free of the home button ares. Screen could only open then 75-80 degrees. Tapr tore. Pried battery out. Replaced on original sticky tape. Restarted fine and about to recycle the charge. Thanks for the kit and all. But 6 demos and 3 inatructions never mentioned this strip! So careful opening it up, please!!

    Michael W Mason - Contestar

    @mikamazn What you’re describing sounds like an iPhone 5s. This guide is for the 5c. Glad to hear things worked out for you.

    Jeff Suovanen -

  4. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Finalizar el proceso de apertura con el iSclack: paso 4, imagen 1 de 2 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Finalizar el proceso de apertura con el iSclack: paso 4, imagen 2 de 2
    • Agarra tu iPhone con fuerza y cierra las palancas del iSclack para separar las ventosas, separando así la pantalla de la carcasa trasera.

    • El iSclack está diseñado para abrir tu iPhone lo suficiente para separar las piezas, pero no tanto como para dañar los cables internos.

    • Separa las dos ventosas de tu iPhone.

    • Ignora los siguientes tres pasos y continúa hasta el Paso 8.

  5. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Abrir el teléfono manualmente: paso 5, imagen 1 de 1
    • Presiona una ventosa sobre la pantalla, justo por encima del botón de Inicio.

    • Asegúrate de que la ventosa se pone completamente sobre la pantalla, para que esté bien fija.

    very, very difficult to get a tight seal on tape. I removed the tape and still can't get a tight seal.

    bromanmoon - Contestar

  6. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Comenzar a levantar el panel frontal: paso 6, imagen 1 de 2 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Comenzar a levantar el panel frontal: paso 6, imagen 2 de 2
    • Asegúrate de que la ventosa está firmemente pegada al panel frontal.

    • Mientras agarras tu iPhone con una mano, empuja hacia arriba la ventosa con la otra mano para separar ligeramente la pantalla frontal de la carcasa trasera.

    • Tómate tu tiempo y aplica una fuerza firme y constante. La pantalla está mucho más ajustada que en otros dispositivos.

    • Con una herramienta de apertura de plástico, empieza a abrir empujando y separando lentamente la carcasa trasera de la parte frontal, a la vez que sigues tirando de la ventosa.

    • Hay varias sujeciones que unen la pantalla frontal a la carcasa trasera, por lo que quizás necesites alternar entre hacer palanca sobre la parte trasera, tirar de la pantalla o ambas a la vez.

    Cover a badly cracked screen with a strip of packing tape first to get a better seal for your suction cup. If it's a super crappy suction cup, moistening it a bit will help as well.

    Dan - Contestar

    Great Idea! I have been doing this for awhile and have never thought to share!

    duston -

    The pry point in this photo is spot on. Just be gentle and maybe come in at a little steeper angle.

    V. Jones - Contestar

    This part ended up being really easy for me. I applied the suction cup just as the picture shows and pulled slowly almost straight up; the screen came off very easily and I didn’t even need to use a plastic prying tool. Not sure why it worked so well but I’m glad!

    Renee - Contestar

    I did it with a guitar pick and no suction cup.

    andrew - Contestar

    Be sure not to use metal pry tools as they may crack the plastic.

    guardian10 - Contestar

  7. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 7, imagen 1 de 1
    • Tira del trozo de plástico de la ventosa para liberar el vacío.

    • Separa la ventosa de la pantalla.

  8. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Abrir el teléfono: paso 8, imagen 1 de 2 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Abrir el teléfono: paso 8, imagen 2 de 2
    • Levanta el extremo del botón de Inicio de la pantalla para tener acceso a los conectores que hay en la parte superior del teléfono.

    • Abre la pantalla hasta que forme un ángulo de unos 90º, y apóyala sobre algo que la mantenga en posición mientras trabajas en el teléfono.

    • Si no se te ocurre qué usar, haz lo siguiente: usa una lata de refresco sin abrir para mantener la pantalla.

    • Coloca una banda elástica de goma para que la pantalla quede fija a la lata mientras trabajas. Esto evitará que torsiones los cables de la pantalla.

    Using a can works really well!

    Amy Dachs - Contestar

    I use an old iPhone box to support the open phone. Set the box up on its end, and rubber band the screen side to the box. It works perfectly!

    Travis Henrick - Contestar

    What do I do if it’s a little sticky and dirty inside?

    sunnydsunset2014 - Contestar

  9. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 9, imagen 1 de 1
    • Separa los dos tornillos Phillips #000 de 1.6 mm que mantienen el soporte del conector metálico de la batería unido a la placa lógica.

    These screws are very tiny and hard to manipulate. The screwdriver is magnetic; which is great to take them out, but makes it hard to put the screws back in, as the screwdriver pulls them from the hole. I solved this problem by using the pointed end of the spudger to put a tiny drop of Elmer's glue in the hole and then insert the screw. You can do this before putting the bracket in place if you want. Then the screw wont pull out by the magnetic driver and make lining up and fastening the screws much easier; at least for me!

    Joe Shirghio - Contestar

    I found that you don't need to disconnect the battery... why bother doing more fiddling with annoyingly tiny screws and obstinate cable connectors when you don't actually have to? Especially when you could only end up causing more damage. As a matter of fact, the original iFixit video didn't bother to disconnect the battery either, but they've since updated the video to include battery disconnection, I guess as a "belt and braces" approach in case the repair-hero forgets to power down the phone first?

    Michael Allen - Contestar

    Disconnecting the battery is a safety precaution, and yes it's worth doing. Even with the phone powered off, there is some danger of blowing the backlight filter fuse if you disconnect the display while the battery is connected. At that point you're no longer looking at a simple DIY repair. Even though it's possible to skip this step and still come out okay, my advice is not to risk it.

    Jeff Suovanen -

    It’s a relatively junky phone, so if it breaks, what the heck. I’m not going to disconnect the battery.

    Zachariah Sampson - Contestar

  10. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 10, imagen 1 de 1
    • Separa el soporte del conector metálico de la batería del iPhone.

  11. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Desconectando el conector de la bateria: paso 11, imagen 1 de 1
    • Utiliza la parte plana de un spudger para cuidadosamente hacer palanca sobre el conector de la batería y desconectarlo de su enchufe en la placa lógica.

    • Ten mucho cuidado de solo hacer palanca en el conector de la batería y no en el enchufe en la placa lógica. Si haces palanca sobre el enchufe de la placa lógica o en dicha placa, podrías destruir el enchufe o dañar los componentes cercanos de la placa.

    Instead of using a spudger, you can use your fingernails too. This is quicker and enables you to feel if you're not accidentally putting on too much pressure or lifting the connector instead of the cable.

    Jona Wolff - Contestar

    Accidentally pulling out the logic board socket is no idle warning - exactly what I did without much effort. I think this shouldn’t be described as ‘prying’ up because it implies needing to use force - but these things actually pop off quite easily with a nudge, which you discover at later steps.

    Peter Hill - Contestar

  12. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 12, imagen 1 de 1
    • Quita los siguientes tornillos Phillips #000 que mantienen conectados el enchufe del cable de la pantalla a la placa base:

    • Dos tornillos de 1.3 mm

    • Un tornillo de 1.7 mm

    • Un tornillo de 3.25 mm

    • Es muy importante vigilar los tornillos de este paso para poder armar el dispositivo de nuevo. Si usas por accidente el tornillo de 3.25 mm o de 1.7 mm en el agujero inferior derecho, dañarás significativamente la placa lógica, lo que hará que el teléfono ya no pueda encenderse adecuadamente.

    • Ten cuidado de no apretar demasiado los tornillos. Si no encajan bien al colocarlos de nuevo, entonces no estás usando el tornillo adecuado, así que no los fuerces.

    I didn't need to remove the front panel to replace the lightning connector. Just prop it up like in Step 8, then skip steps 12-16.

    jacobstevens - Contestar

    I always put my screws in a magnet tray and place the screws in the exact position they were taken out. The magnet tray holds the screws tight in the position I put them in. No chasing on the floor looking for small screws that you brushed off the table.

    Fredrick Apel - Contestar

    I always take a picture of the phone, print it out, then use scotch tape to tape the screws onto the picture in the location where they go. You don't lose the screws and you always know where they go for re-assembly

    K Jansen - Contestar

    good tip! but instead of taking & printing a picture of your own phone, you probably could just print the color coded pic from this step (assuming everything on your phone is exactly the same).

    travismlive -

    When reassembling, the screw holder that the screws screw into came off the board. Is there a way to superglue that back in?

    Chandler Perez - Contestar

    no, do not use super-glue. Quite some of these ‘screw-holders’ are screws themselves with e hollow tread in the head (didn’t find the correct naming for it) - just like the things you screw into a PC case and fasten the mainboard on.

    akronymus -

    did NOT remove the front entirely. its not necessary to do this to remove the battery. these are only precautionary steps in case your clumsy or you feel you might not be able to manage it without. as always, be cautious.

    matt - Contestar

    Agree. Step 12 is unnecessary if one is extremely careful.

    Christopher -

    *warning* … this connector assembly is very messy to re-build. Next time I change such a battery, I’ll try to get it out carefully *without* detaching the display unit. My resumée: *never* unscrew more things than necessary. These things are not M five (5 mm bolt diameter) like on a bike, these are M zero-point-five. Even for a smirf, this is tiny stuff.

    akronymus - Contestar

    is it necessary to remove these screws in order to remove the battery?

    Ali Ahsan - Contestar

    Hi Ali,

    You can choose to not remove those screws and still be able to take the battery out. Be very careful supporting the display, or you may tear the display cables and damage your screen.

    Arthur Shi -

  13. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 13, imagen 1 de 1
    • Separa el soporte del cable del panel frontal de la placa lógica.

  14. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Desconectar los cables de la pantalla: paso 14, imagen 1 de 2 Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Desconectar los cables de la pantalla: paso 14, imagen 2 de 2
    • Usa una herramienta de apertura de plástico o una uña para desconectar la cámara y el conector del cable del sensor.

    • Asegúrate de que solo empujas el conector y no el enchufe de la placa lógica.

    You might get a more “modernised” part from eBay (for this very model, iPhone 5c) which has an ENTIRE CABLE missing… if you look closely, it’s been re-directed into the middle cable. And it all works perfectly, touch screen, and display. So it’s a optimisation.

    In summary - if you get this version of the screen, you only need to deal with 2 cables, not 3. The rightmost socket will remain empty.

    domarius - Contestar

  15. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 15, imagen 1 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 15, imagen 2 de 3 Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 15, imagen 3 de 3
    • Asegúrate de que la batería está desconectada antes de desconectar o reconectar los cables en este paso.

    • Usa una herramienta de apertura de plástico o tus uñas para desconectar el cable LCD.

    • Los conectores LCD y del digitalizador están en el mismo cable, así que al levantar el conector LCD ambos conectores se separarán. Comprueba que ambos cables están totalmente desconectados antes de separar la pantalla por completo.

    • Al montar tu teléfono de nuevo, el cable LCD podría desconectarse de su conector. Una pantalla en blanco o con líneas blancas sería un indicativo de una mala conexión debido a este problema. Si esto ocurre, reconecta el cable y haz un "power cycle". El "power cycle" simplemente consiste en desconectar y reconectar la batería.

    I replaced the broken front panel of the iPhone 5c and got the "famous white stripes" on the new screen. Reading about all kind of problems that the lcd/digitizer cable contacts may cause, I compared the cable connectors of the original Apple and the replacement part I bought online with a 35x magnifying glass. The quality difference was visible: The white description on the original part on the cable next to the connector is: 821-1784-A, while the inferior replacement part is: 821-1784-02. Check out the two numbers online and insist getting the "A" to avoid future troubles !!!

    Harold Wallner - Contestar

    This person above is not knowledgeable. That number is a camera proxy part number, not the lcd or digitizer number. It changes with production date, both for original and aftermarket ones. A, B, D, 02, 04, 08 etc. Can all be either or.

    vince -

    Apple uses numerical revisions (-02) for pre-production parts, and alpha revisions (-A) for production revisions. It looks like you got a preproduction assembly, or a knock-off.

    terrymccallum -

    There are, in fact, three connectors in this step, not two. The front-facing camera and digitizer connector (Step 11) is really difficult to align when you put it back. Took me about 15 minutes before I succeeded.

    Now I have a different problem. Everything works just dandy, EXCEPT:

    Towards the bottom of the screen (in portrait) there is a horizontal line that is dead to the touch. For example, on the keyboard, I can use the spacebar, but not C V B N M, etcetera.

    Three possibilities in my mind: One, when I dropped it, something else besides the glass and digitizer, etc, was damaged.

    Two: I did not replace the cables correctly. This seems unlikely. They all "clicked" into place and stayed there.

    Three: The digitizer supplied is faulty.

    Comments? Which cable/connector could be causing this -- if it is that?

    piet - Contestar

    Take apart, Clean Connections, Put back together.... If same problem sounds like a fault part...

    duston -

    When reassembling the iPhone 5c, I used the flat end of the spudger to press on the connectors and maintain them while replacing the front panel on the body of the iPhone.

    The third and "deepest" connector no longer slips out of its socket, which it did before holding the whole lot with the spudger.

    jimbbo - Contestar

    If the ESD plate covering the connectors is properly re-attached to the phone, you should not have to do this. The cover holds all the connectors in place just fine.

    iBroke -

    I replaced the display assembly to resolve an issue with the phone not responding to any touch input. I assumed it was a bad digitizer. However, I have the same problem with the new display assembly—no touch response at all. The phone starts up fine and the screen works, I just can’t “slide to unlock”. This is also preventing me from downloading photos from the phone since I can’t enter the passcode. I have cleaned the connections and reseated the cables. Is it possible this is a problem on the logic board? If so, is there any way to get the photos off the phone since I can’t enter the passcode on the screen?

    ewistey - Contestar

  16. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Separar pantalla y carcasa trasera: paso 16, imagen 1 de 1
    • Separa la pantalla de la carcasa trasera.

    Very clear and percise.

    Jessica Fader - Contestar

  17. Reemplazo del cable de cinta del botón de inicio del iPhone 5c, Cable de cinta del botón de inicio: paso 17, imagen 1 de 1
    • Retire los dos tornillos Phillips #000 de 1,3 mm que sujetan el soporte del botón de inicio al ensamblaje de la pantalla.

    Ok the screw are just the 2 highlighted in red. Note that if you fix them too tight the button will lose some space. I suggest to fix them tight and then to unscrew them of 180° just to remove some pressure. Then try the home button movement: if it’s ok go ahead otherwise if it has no freedom to move unscrew again a little bit

    Francesco Garuti - Contestar

  18. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 18, imagen 1 de 2 Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 18, imagen 2 de 2
    • Use una herramienta de apertura de plástico para hacer palanca en el borde del cable plano del botón de inicio del ensamblaje de la pantalla.

    • Comience debajo de los puntos de contacto a la derecha y trabaje hacia la izquierda.

    • Comenzar desde la izquierda e ir a la derecha puede romper el cable de cinta. Los contactos están bien adheridos al panel frontal y deben retirarse primero.

    • Si tiene problemas para deslizar la herramienta de apertura de plástico debajo de los puntos de contacto, voltee la herramienta y presione suavemente contra el lado derecho del cable de contacto para aflojar el adhesivo, luego intente nuevamente.

    If you have an iOpener, I STRONGLY suggest placing it on top to loosen the glue. Once I heated the surface, it came off with little difficulty.

    Curt Veenstra - Contestar

    Achtung! Am oberen linken Eck bei den orangenen Kontakten sitzen zwei winzige elektronische Bauteile. Diese können bei unvorsichtiger Arbeit und falls das Kabel sehr fest sitzt abbrechen. Sie sind mit ein bisschen Kleber abgedeckt.

    iRolleder - Contestar

  19. Reemplazo del cable de cinta del botón de inicio del iPhone 5c: paso 19, imagen 1 de 1
    • Retire el cable plano del botón de inicio del ensamblaje de la pantalla.

    • Si está instalando un nuevo cable de cinta para el botón de inicio, asegúrese de mantener el soporte de metal y transfiéralo a su nuevo cable de cinta durante el reensamblaje.

    Wenn der Home Button nach dem Austausch immer noch nicht funktioniert, sollte man sich die beiden kleinen Kontakte anschauen, die auf der Platine an einem Flachbandkabel sind und auf die in dieser Anleitung zu sehenden messingfarbenen Kontakte drücken. Ist einer dieser beiden Kontakte defekt, muss man den Lightning Anschluss ersetzen. Kostet zwar unter 5€, ist aber ziemlich aufwändig, da der Akku ausgebaut werden muss.

    Skyynet - Contestar

Conclusión

Para volver a armar su dispositivo, siga estas instrucciones en orden inverso.

48 personas más completaron esta guía.

Un agradecimiento especial a estos traductores:

en es

100%

¡ Luis Roberto nos está ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›

7 comentarios

Good instructions; I did managed to disconnect the lcd connector, but easy enough to pop back in again. No luck on getting my home button to work though - maybe the button was the thing that needed replacing.

bairandrea - Contestar

This guide should be named "How To Remove The Home Button Ribbon Cable". Saying that this guide is "How To Replace..." is misleading because there are no steps that show how to install a new home button which should include how to reinstall the cable while reapplying soft adhesive. Also, steps 9-16 are not relevant to this guide. Looks like the repair tech and the web developer need to talk to each other. The web developer should have required the tech to perform a dry run of the steps posted which is a standard web development process.

jjovanw - Contestar

As stated in the guide conclusion, installation/replacement is the reverse of removal. The replacement ribbon cable will already have the adhesive applied; there's no need to overcomplicate things with additional steps. Steps 9-11 are for disconnecting the battery, which is standard procedure for working on consumer electronics. Steps 12-16 can be skipped if you are comfortable working on the home button while the display is still attached, but you risk damaging your display ribbon cables if you're not careful, turning a $15 repair into a $75 repair.

Jeff Suovanen -

The ribbon I received has a small white piece of paper on it. Do I have to remove that to get to the adhesive ?

neil campbell - Contestar

Yes, you have to remove the piece of paper or plastic to install the new cable.

Skyynet -

in step 18 there is a screw attached to the metal back plate in the picture to the right top of the home button ribbon cable. In picture 19 it is not shown. does this need to be removed also?

Carl Gulick - Contestar

@cfgjm1 It’s not related to replacing the home button components, so if that’s all you’re doing you can leave it alone. The screw didn’t go anywhere BTW—it’s just blocked from view by the home button cable in Step 19.

Jeff Suovanen -

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 2

Ultimos 7 días: 5

Ultimos 30 días: 16

Todo El Tiempo: 21,251