Reemplaza el ensamblaje de altavoz y conector Lightning del iPhone 5

Introducción

Pre-requisito interno para remover el ensamblaje de conector Lightning y altavoz.

Qué necesitas

Paso 1 Ensamblaje de altavoz y conector Lightning

Reemplaza el ensamblaje de altavoz y conector Lightning del iPhone 5, Ensamblaje de altavoz y conector Lightning: paso 1, imagen 1 de 1

Remueve los siguientes tornillos que sujetan el recinto del ensamblaje del conector Lightning y altavoz a la caja trasera.
Un tornillo Phillips de 2.5 mm
Dos tornillos Phillips de 3.3 mm
Un tornillo Phillips de 2.9 mm
Dos tornillos Phillips de 1.5 mm
Un tornillo Phillips de 2.8 mm

Traducir

Every step after this one is vague and hard to understand. Seems to be a lot missing. Proceed with extreme caution!

Joe Wasser - 11 de may. de 2017 Contestar

Paso 2

Reemplaza el ensamblaje de altavoz y conector Lightning del iPhone 5: paso 2, imagen 3 de 3

Usa el extremo plano de un spudger para levantar los cables del recinto del ensamblaje de conector Lightning y altavoz de la caja trasera.
Asegúrate de colocar el spudger debajo del cable cinta grande conectado al ensamblaje ya que hacer palanca en el resto del ensamblaje podría resultar en una ruptura.

Traducir

this is NOT the right way to remove the speaker, anyone following this guide will do unnecessary damage to the phone.

Speaker is one of the "official" serviceable part of iPhone 5. Which means you don't have to remove the logic board and the battery. Skip straight to step 27, peel up the home button contact flex, remove the red, blue, yellow and the green screw, peel loose the grounding flex stuck around the headphone jack, then remove the flex and the speaker as one part. NEVER remove the lightning connector flex unless you really need to.

Tom Chai - 12 de abr. de 2013 Contestar

I agree, there is no need to remove the battery or the main board, simply remove the two screws on the right hand side of the buzzer (the larger one on the right and smaller one by dock) and remove the screw next to the home button contact, the buzzer simply slides out, 5 minute job.

g4tch - 19 de feb. de 2014 Contestar

Heyi successfully took out this speaker and jack but i found 4 small rings and i dont know where they were placed

Shaiz Qadri - 4 de dic. de 2016 Contestar

Paso 3

Reemplaza el ensamblaje de altavoz y conector Lightning del iPhone 5: paso 3, imagen 3 de 3

Remueve el ensamblaje del conector de Lightning y altavoz de du caja trasera.
Ten cuidado de no perder la arandela pequeña de metal en el recinto del altavoz o las cuatro arandelas pequeñas de metal debajo de los tornillos del conector Lightning.

Traducir

At this point I ended up with four (4) washers. I put back 3 under the two 1.5mm and the one 2.9mm screw but have no idea where the 4th should go.

Dirk - 29 de ago. de 2013 Contestar

What are the metal washers for?

Whatever - 30 de oct. de 2013 Contestar

Make sure to clean any bits of golden glue left on the phone case

andrewcilia - 15 de dic. de 2013 Contestar

i noticed that i broke tip of the loudspeaker cover flex under washer, and now my iphone won't turn on :(

mate - 31 de dic. de 2013 Contestar

Do you know where I can get these washers? I lost one in the disassembly process.

Scott - 22 de mar. de 2014 Contestar

The metal washers appear to have come from the bottom side of the lightning connector. Underneath the four screws. Two of mine were stuck on the old part that I had removed. I noticed this after installing the parts.

Rene Jeddore - 29 de mar. de 2014 Contestar

Any idea what is the strip which is stuck on the speaker, which helps connect the two screws? does it have any specific functionality or is it just to keep the speaker in place?

I see that it just connects two end points to the iphone body.

madhucherla - 31 de dic. de 2014 Contestar

That part is the cellular antenna. iPhone 5 Cellular Antenna

slessard - 12 de ene. de 2015

After Removing Speaker and Lightning Assembly , please take care to remove plastic washers glued to case. Those are important because gives protection and some isolation from outside around the connectors and between bare speaker and case

luis - 11 de abr. de 2015 Contestar

I am trying to find these washers that go under the lightning connector as to where I can find an extra one of these for a repair and also need some help figuring out after replacing power cable, LCD and screen, lightning connector and both flex cables on the motherboard, the back case and the battery why the iPhone 5 is not charging or powering on... If you can help me figure out this issue I would greatly appreciate it.

Could one missing washer cause this to be the issue.

jweika - 23 de abr. de 2015 Contestar

Hi, I proceeded to the replacement of the microphone iphone 5 but now the voice is distant and muffled and the metal whaser I did not understand where I have to relocate. Can you help me?

Thank you

Fabio - 6 de abr. de 2017 Contestar

Upon reassembly, I had inadvertently routed the cellular antenna cable under the speaker (next to the back of the case). I had to do a bit of backtracking to free it up, and correctly route the cable *above* the speaker so it could reach the connector on the logic board.

Fanboy - 31 de dic. de 2017 Contestar