Saltar al contenido principal
  1. Antes de desmontar tu iPhone, asegúrate de que este apagado. La caja posterior de tu iPhone 4 puede fijarse bien con dos tornillos Phillips #000 o bien con tornillos Apple de 5-Puntos (segunda imagen). Comprueba cuáles tienes y asegúrate de que tienes el destornillador adecuado para retirarlos.
    • Antes de desmontar tu iPhone, asegúrate de que este apagado.

    • La caja posterior de tu iPhone 4 puede fijarse bien con dos tornillos Phillips #000 o bien con tornillos Apple de 5-Puntos (segunda imagen). Comprueba cuáles tienes y asegúrate de que tienes el destornillador adecuado para retirarlos.

    • Retira los dos tornillos Pentalobe o Phillips #000 de 3.6 mm que están junto al conector para el cargador.

    • El Destornillador de 5-Puntos solo de ser utilizado una vez, ya que tiene la posibilidad de barrer los tornillos.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Push the rear panel toward the top edge of the iPhone. The panel will move about 2 mm.
    • Push the rear panel toward the top edge of the iPhone.

    • The panel will move about 2 mm.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Pinch the rear panel with your fingers and lift it  away from the iPhone. Alternatively, use a Small Suction Cup .
    • Pinch the rear panel with your fingers and lift it away from the iPhone. Alternatively, use a Small Suction Cup .

    • Be careful not to damage the plastic clips attached to the rear panel.

    • If you are installing a new rear panel, be sure to remove the plastic protective sticker from the inside of the camera lens and the sticker from the large black area near the lens.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.
    • Remove the single 2.5 mm Phillips screw securing the battery connector to the logic board.

    • Some devices may have two screws, one of which holds down the contact pad which is located above the screw indicated in red in the photo.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.
    • Use a plastic opening tool to gently pry the battery connector up from its socket on the logic board.

    • Pry from the top and bottom of the connector bracket—there isn't as much of an overhang on the sides, and you may damage the connector.

    • Be very careful to only pry up on the battery connector and not the socket on the logic board. If you pry up on the logic board socket, you may break it entirely.

    • Remove the metal clip covering the antenna connector.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Use the clear plastic pull tab to gently lift the battery out of the iPhone. If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive. Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.
    • Use the clear plastic pull tab to gently lift the battery out of the iPhone.

    • If the tab breaks before the battery is freed, apply a few drops of high concentration (over 90%) isopropyl alcohol under the edge of the battery. Wait about one minute for the alcohol solution to weaken the adhesive. Carefully slide a spudger under the battery tab to release the adhesive.

    • Prying in other places may cause damage. Don't try to forcefully lever the battery out. If needed, apply a few more drops of alcohol to further weaken the adhesive. Never deform or puncture the battery with your pry tool.

    • If there's any alcohol solution remaining in the phone, carefully wipe it off or allow it to air dry before installing your new battery.

    • If your replacement battery came in a plastic sleeve, remove it before installation by pulling it away from the the ribbon cable.

    • Before reconnecting the battery connector, be sure the contact clip (shown in red) is properly positioned next to the battery connector.

    • Before reassembly, clean metal-to-metal contact points with a de-greaser such as windex. The oils from your fingers have the potential to cause wireless interference issues.

    • Perform a hard reset after reassembly. This can prevent several issues and simplify troubleshooting.

  7. Este paso está sin traducir. Ayuda a traducirlo

    Use a pair of tweezers to remove the small strip of tape covering the back of the volume buttons.
    • Use a pair of tweezers to remove the small strip of tape covering the back of the volume buttons.

    • Be sure to peel the tape starting from nearest the top of the phone.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Remove the three Phillips screws securing the volume button bracket to the outer case.
    • Remove the three Phillips screws securing the volume button bracket to the outer case.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Use a pair of tweezers to gently pull the volume button bracket slightly away from the outer case.
    • Use a pair of tweezers to gently pull the volume button bracket slightly away from the outer case.

  10. Este paso está sin traducir. Ayuda a traducirlo

    Remove the volume button from the iPhone.
    • Remove the volume button from the iPhone.

Linea de Meta

85 personas más completaron esta guía.

Documentos Adjuntos

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 4

Ultimos 30 días: 17

Todo El Tiempo: 122,947