Saltar al contenido principal
  1. Si el cristal de la pantalla está agrietado, mantén la rotura contenida y evita que se produzcan daños corporales durante la reparación pegando el cristal con cinta adhesiva. Coloca tiras superpuestas de cinta de embalar transparente sobre la pantalla del iPhone hasta cubrir toda la cara. Esto mantendrá los fragmentos de cristal contenidos y proporcionará integridad estructural al hacer palanca y levantar la pantalla.
    • Si el cristal de la pantalla está agrietado, mantén la rotura contenida y evita que se produzcan daños corporales durante la reparación pegando el cristal con cinta adhesiva.

    • Coloca tiras superpuestas de cinta de embalar transparente sobre la pantalla del iPhone hasta cubrir toda la cara.

    • Esto mantendrá los fragmentos de cristal contenidos y proporcionará integridad estructural al hacer palanca y levantar la pantalla.

    • Utiliza gafas de seguridad para proteger tus ojos de los cristales que se desprendan durante la reparación.

  2. Este paso está sin traducir. Ayuda a traducirlo

    Remove the two Phillips #00 screws from the dock-connector end of the iPhone.
    • Remove the two Phillips #00 screws from the dock-connector end of the iPhone.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.
    • Remove the metal handle from the suction cup. It's easier and safer to grip the suction cup's base instead of the metal handle.

    • Be very careful when opening the iPhone so that the cables under the display are not severed.

    • There is a rubber gasket between the silver front bezel and black display assembly. A bit of force is required in this step to separate the iPhone's display assembly.

    • Use a small suction cup near the Home button to gently pull up the bottom portion of the iPhone's display assembly.

    • If the display assembly is too damaged to allow the suction cup to adhere, tape with a strong adhesive such as duct tape may be used.

  4. Este paso está sin traducir. Ayuda a traducirlo

    The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.
    • The display assembly is still connected to the iPhone by several cables, so don't try to remove it entirely just yet.

    • Rotate the display assembly up until it is at an angle of approximately 45 degrees.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."
    • Continue to hold the display assembly with one hand, and use your other hand and a spudger to disconnect the black ribbon cable labeled "1."

  6. Este paso está sin traducir. Ayuda a traducirlo

    Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.
    • Rotate the display assembly up until it is roughly vertical. This will allow easier access for disconnecting the remaining cables.

    • Use a spudger to disconnect the black ribbon cable labeled "2."

  7. Este paso está sin traducir. Ayuda a traducirlo

    Use a spudger to flip up the black plastic tab holding the remaining ribbon cable in place. The black will rotate up 90 degrees, releasing the ribbon cable.
    • Use a spudger to flip up the black plastic tab holding the remaining ribbon cable in place. The black will rotate up 90 degrees, releasing the ribbon cable.

    • The tab is very fragile, so be careful when flipping it up to unlock the cable and down to lock the cable.

    • The plastic tab may be white (instead of black) on some iPhone models.

    • Slide the ribbon cable out of its connector, and remove the display assembly from the iPhone.

Linea de Meta

228 personas más completaron esta guía.

i went through the whole process, but my home button does not work anymore. it was fine when I started - its it possible, that one ribbon is not fully attached ore is there any other solution? Thanks for any advice!

Jakob

JakobBartke - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 1

Ultimos 7 días: 4

Ultimos 30 días: 11

Todo El Tiempo: 301,661