Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Inserta una herramienta de expulsión de la tarjeta SIM o un clip en el orificio junto a la toma de auriculares.
-
Presiona el clip para papel hasta que salte la bandeja de la tarjeta SIM.
-
-
-
Inserta una herramienta de apertura de iPod en el espacio entre la cubierta de la antena y el marco frontal. La cuña de la herramienta debe apuntar hacia la cubierta de la antena. Deslice la herramienta alrededor de la esquina y hacia arriba hasta que llegue al soporte de metal.
-
Repita el mismo procedimiento en el otro lado del conector de la base.
-
-
-
Quita los tres tornillos Phillips # 00 que sujetan el panel posterior al iPhone.
-
-
-
-
Levanta el panel posterior tirando de la selección dental hacia la derecha en un movimiento rápido. Aplica una fuerza perpendicular al plano del ensamblaje de la pantalla. Es posible que tengas miedo de ir rápido, pero ir más despacio es más probable que reduzca el caso.
-
El panel posterior todavía está conectado al iPhone por el cable de la toma de auriculares, por lo que aún no quites completamente el panel posterior del iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel up the orange tape securing the white antenna cable to the side of the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to disconnect the two antenna cables from the communications board. Apple used a small dab of glue on these connections, which may make removing the antenna connections harder.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 3 screws:
-
One Phillips #00 screw securing the logic board to the iPhone near the camera.
-
Two Phillips #00 screws, one on either corner of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to disconnect the camera connector.
-
Lift the camera out of the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Working from the edge opposite the battery connectors, insert a spudger between the battery and the plastic frame and pry up on the battery. It is attached to the casing with an adhesive, but should slowly come free.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide a spudger beneath the logic board on the side opposite the battery connector and pry up slightly. Don't lift up too far, because there are still four attached connectors on the bottom of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
In a similar manner, slide a spudger beneath the logic board where the camera was. Again, don't lift up too far yet as there are still four attached connectors on the bottom of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift up the logic board slightly and slide a spudger beneath the logic board to disconnect the display ribbon cable.
-
After freeing the first connector, slide the spudger further towards the battery and the center of the iPhone to disconnect the speaker connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Go to the other side of the logic board and use a spudger to disconnect the touch sensor cable on the under side of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide a spudger beneath the black locking bar and pry up to rotate the bar 90 degrees (the bar is already rotated in the picture).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Hold both the battery and the logic board assembly and slide both parts away from the orange antenna and out of the iPhone.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
There are two stacked circuit boards on the iPhone. The communcations board is on the top, and the logic board is located on the bottom.
-
To separate the boards, insert a spudger into the gap in the metal shielding as shown. Carefully pry with the spudger to loosen the connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to separate the two boards. The silver metal shielding may not immediately separate. If necessary, work around the edge of the board to separate the metal shielding.
-
Cancelar: No complete esta guía.
32 personas más completaron esta guía.