Saltar al contenido principal

Qué necesitas

  1. iPhone 11 Lower Speaker Replacement, Remove the pentalobe screws: paso 1, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Remove the pentalobe screws: paso 1, imagen 2 de 2
    • Before you begin, discharge your iPhone battery below 25%. A charged lithium-ion battery can catch fire and/or explode if accidentally punctured.

    • Power off your iPhone before beginning disassembly.

    • Remove the two 6.7 mm-long pentalobe screws at the bottom edge of the iPhone.

    • Opening the iPhone's display will compromise its waterproof seals. Have replacement seals ready before you proceed past this step, or take care to avoid liquid exposure if you reassemble your iPhone without replacing the seals.

  2. iPhone 11 Lower Speaker Replacement, Heat the lower edge of the phone: paso 2, imagen 1 de 1
    • Heating the lower edge of the iPhone helps soften the adhesive securing the display, making it easier to open.

    • Use a hairdryer or heat gun or prepare an iOpener and apply it to the lower edge of the iPhone for about a minute.

  3. iPhone 11 Lower Speaker Replacement, Anti-Clamp instructions: paso 3, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Anti-Clamp instructions: paso 3, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Anti-Clamp instructions: paso 3, imagen 3 de 3
    • The next two steps demonstrate the Anti-Clamp, a tool we designed to make the opening procedure easier. If you aren't using the Anti-Clamp, skip down two steps for an alternate method.

    • For complete instructions on how to use the Anti-Clamp, check out this guide.

    • Pull the blue handle towards the hinge to disengage opening mode.

    • Position the suction cups near the bottom edge of the iPhone—one on the front, and one on the back.

    • Push down on the cups to apply suction to the desired area.

    • If you find that the surface of your device is too slippery for the Anti-Clamp to hold onto, you can use packing tape to create a grippier surface.

  4. iPhone 11 Lower Speaker Replacement: paso 4, imagen 1 de 3 iPhone 11 Lower Speaker Replacement: paso 4, imagen 2 de 3 iPhone 11 Lower Speaker Replacement: paso 4, imagen 3 de 3
    • Push the blue handle away from the hinge to engage opening mode.

    • Turn the handle clockwise until you see the cups start to stretch.

    • Make sure the suction cups remain aligned to each other. If they begin to slip out of alignment, loosen the suction cups slightly and realign the arms.

    • Wait one minute to give the adhesive a chance to release and present an opening gap.

    • Insert an opening pick at the bottom edge when the Anti-Clamp creates a large enough gap.

    • If the Anti-Clamp doesn't create a sufficient gap, apply more heat to the area and rotate the handle clockwise half a turn.

    • Don't crank more than a half a turn at a time, and wait one minute between turns. Let the Anti-Clamp and time do the work for you.

    • Skip the next two steps.

  5. iPhone 11 Lower Speaker Replacement: paso 5, imagen 1 de 2 iPhone 11 Lower Speaker Replacement: paso 5, imagen 2 de 2
    • If you're using a single suction handle, apply it to the bottom edge of the phone, while avoiding the curved portion of the glass.

    • If your display is badly cracked, covering it with a layer of clear packing tape may help the suction cup to stick. Alternatively, you can use very sticky tape instead of the suction cup. Or if all else fails, you can superglue the suction cup to the broken screen.

  6. iPhone 11 Lower Speaker Replacement, Lift the display slightly: paso 6, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Lift the display slightly: paso 6, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Lift the display slightly: paso 6, imagen 3 de 3
    • Pull up on the suction cup with firm, constant pressure to create a slight gap between the front panel and rear case.

    • Insert an opening pick into the gap.

    • The watertight adhesive holding the display in place is very strong; creating this initial gap takes a significant amount of force. If you're having a hard time opening a gap, apply more heat, and gently rock the screen up and down to weaken the adhesive until you create enough of a gap to insert your tool.

  7. iPhone 11 Lower Speaker Replacement, Separate the screen adhesive: paso 7, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Separate the screen adhesive: paso 7, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Separate the screen adhesive: paso 7, imagen 3 de 3
    • Slide the opening pick around the lower left corner and up the left edge of the iPhone, slicing through the adhesive holding the display in place.

    • Don't insert the opening pick too far into the iPhone, or you may cause damage to internal components.

  8. iPhone 11 Lower Speaker Replacement: paso 8, imagen 1 de 3 iPhone 11 Lower Speaker Replacement: paso 8, imagen 2 de 3 iPhone 11 Lower Speaker Replacement: paso 8, imagen 3 de 3
    • Re-insert your pick at the bottom edge of the iPhone, and slide it up the right side to continue separating the adhesive.

    • Don't insert the pick very far, or you may damage the display cables along this side of the iPhone. Insert it only a few millimeters, or about the width of the display bezel.

  9. iPhone 11 Lower Speaker Replacement: paso 9, imagen 1 de 3 iPhone 11 Lower Speaker Replacement: paso 9, imagen 2 de 3 iPhone 11 Lower Speaker Replacement: paso 9, imagen 3 de 3
    • The top edge of the display is secured with both glue and clips.

    • Gently pull the right edge of the display down slightly (in the direction of the Lightning port).

    • Insert your pick into the top-right corner of the phone.

  10. iPhone 11 Lower Speaker Replacement: paso 10, imagen 1 de 2 iPhone 11 Lower Speaker Replacement: paso 10, imagen 2 de 2
    • Continue pulling the display down (toward the Lightning port) as needed in order to make a gap large enough for the pick.

    • Slide the pick to the top left corner and cut any remaining adhesive securing the display.

    • Again, don't insert the pick more than a few millimeters—about the width of the display bezel—or you may damage the Face ID sensor array.

  11. iPhone 11 Lower Speaker Replacement, Remove the suction cup: paso 11, imagen 1 de 1
    • Pull the small nub on the suction cup to detach it from the front panel.

  12. iPhone 11 Lower Speaker Replacement, Open the iPhone: paso 12, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Open the iPhone: paso 12, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Open the iPhone: paso 12, imagen 3 de 3
    • Open the iPhone by swinging the display up from the left side, like the back cover of a book.

    • Don't try to fully separate the display yet, as several fragile ribbon cables still connect it to the iPhone's logic board.

    • Prop the display up against something sturdy.

    • During reassembly, lay the display in position, align the clips along the top edge, and carefully press the top edge into place before snapping the rest of the display down. If it doesn't click easily into place, check the condition of the clips around the perimeter of the display and make sure they aren't bent.

  13. iPhone 11 Lower Speaker Replacement, Display Assembly: paso 13, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Display Assembly: paso 13, imagen 2 de 2
    • To access the screws in the following step, tilt the display by slightly lifting its lower edge.

    • Be careful not to strain or tear the display cables.

    • Use a Y000 driver to remove the three 1.1 mm-long screws securing the battery connector bracket.

    • Throughout this repair, keep track of each screw and make sure it goes back exactly where it came from.

    • During reassembly, this is a good point to power on your iPhone and test all functions before you seal the display in place. Be sure to power your iPhone back down completely before you continue working.

  14. iPhone 11 Lower Speaker Replacement, Remove the battery connector cover: paso 15, imagen 1 de 1
    • Remove the bracket.

  15. iPhone 11 Lower Speaker Replacement, Disconnect the battery: paso 16, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Disconnect the battery: paso 16, imagen 2 de 2
    • Use a spudger or a clean fingernail to pry the battery connector up from its socket on the logic board.

    • Try not to damage the black silicone seal surrounding this and other board connections. These seals provide extra protection against water and dust intrusion.

    • Bend the connector slightly away from the logic board to prevent it from accidentally contacting the socket.

  16. iPhone 11 Lower Speaker Replacement, Unscrew the logic board cover screws: paso 17, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Unscrew the logic board cover screws: paso 17, imagen 2 de 2
    • Use a Y000 driver to remove the five 1.1 mm screws securing the logic board cover bracket.

  17. iPhone 11 Lower Speaker Replacement, Remove the logic board cover bracket: paso 18, imagen 1 de 1
    • Remove the bracket.

  18. iPhone 11 Lower Speaker Replacement, Disconnect the display: paso 19, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Disconnect the display: paso 19, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Disconnect the display: paso 19, imagen 3 de 3
    • Use a spudger or a fingernail to disconnect the LCD panel cable connector.

    • Disconnect the digitizer connector next to it.

  19. iPhone 11 Lower Speaker Replacement, Disconnect the front sensors: paso 20, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Disconnect the front sensors: paso 20, imagen 2 de 2
    • Use the point of a spudger or a fingernail to disconnect the front panel sensor assembly connector.

  20. iPhone 11 Lower Speaker Replacement, Remove the display assembly: paso 21, imagen 1 de 1
  21. iPhone 11 Lower Speaker Replacement, Remove the lower bracket screws: paso 22, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Remove the lower bracket screws: paso 22, imagen 2 de 2
    • Using a Phillips driver, remove the five screws securing the bracket below the Taptic engine and speaker:

    • Four 1.6 mm screws

    • One 1.3 mm screw

  22. iPhone 11 Lower Speaker Replacement, Remove the lower bracket: paso 23, imagen 1 de 1
    • Remove the lower bracket.

  23. iPhone 11 Lower Speaker Replacement, Remove the Taptic Engine connector tape: paso 24, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Remove the Taptic Engine connector tape: paso 24, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Remove the Taptic Engine connector tape: paso 24, imagen 3 de 3
    • Use tweezers to lift and remove the black tape and rubber pad covering the Taptic Engine connector.

    • Use a little heat from a hair dryer or iOpener to make the tape easier to peel up and re-adhere later.

  24. iPhone 11 Lower Speaker Replacement, Unscrew the lower speaker: paso 25, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Unscrew the lower speaker: paso 25, imagen 2 de 2
    • Remove the five screws securing the speaker and brackets:

    • One 1.9 mm Phillips screw

    • One 2.3 mm Phillips screw

    • One 3.1 mm standoff screw

    • Two 1.6 mm Phillips screws

  25. iPhone 11 Lower Speaker Replacement, Remove the grounding clip: paso 26, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Remove the grounding clip: paso 26, imagen 2 de 2
    • Remove the small grounding clip on the top right corner of the speaker.

  26. iPhone 11 Lower Speaker Replacement, Remove the Taptic Engine connector cover: paso 27, imagen 1 de 1
    • Remove the Taptic Engine connector cover.

  27. iPhone 11 Lower Speaker Replacement, Remove the speaker standoff screw: paso 28, imagen 1 de 3 iPhone 11 Lower Speaker Replacement, Remove the speaker standoff screw: paso 28, imagen 2 de 3 iPhone 11 Lower Speaker Replacement, Remove the speaker standoff screw: paso 28, imagen 3 de 3
    • Lift and push aside the small board covering the remaining speaker screw in the bottom right corner of the iPhone.

    • Remove the 2.4 mm standoff screw underneath.

  28. iPhone 11 Lower Speaker Replacement, Loosen the speaker: paso 29, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Loosen the speaker: paso 29, imagen 2 de 2
    • Insert a spudger under the top edge of the speaker, near the edge of the iPhone's case.

    • Gently pry up and lift the top edge of the speaker.

  29. iPhone 11 Lower Speaker Replacement: paso 30, imagen 1 de 2 iPhone 11 Lower Speaker Replacement: paso 30, imagen 2 de 2
    • Hold the speaker by its side edges and rock it side-to-side, separating the adhesive securing it to the bottom edge of the iPhone.

    • Pull the speaker away from the bottom edge of the iPhone until the adhesive gasket separates.

  30. iPhone 11 Lower Speaker Replacement, Remove the speaker: paso 31, imagen 1 de 2 iPhone 11 Lower Speaker Replacement, Remove the speaker: paso 31, imagen 2 de 2
    • Remove the speaker.

    • Optionally, to help protect against water and dust intrusion, replace the speaker's adhesive gasket during reassembly:

    • Peel away any remaining adhesive with tweezers.

    • Prep the area underneath by cleaning it with a bit of isopropyl alcohol and a lint-free cloth or coffee filter so that the gasket adheres properly.

    • Install a new gasket onto the speaker, and then install the speaker.

Conclusión

Compare your new replacement part to the original part—you may need to transfer remaining components or remove adhesive backings from the new part before installing.

To reassemble your device, follow these instructions in reverse order.

Repair didn’t go as planned? Try some basic troubleshooting, or ask our iPhone 11 Answers community for help.

14 personas más completaron esta guía.

Jeff Suovanen

Miembro Desde 06/08/13

401,982 Reputación

261 Guías creadas

Equipo

iFixit Miembro de iFixit

Community

141 Miembros

15,848 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 47

Ultimos 7 días: 449

Ultimos 30 días: 1,954

Todo El Tiempo: 30,485