Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
-
Si el vidrio de tu pantalla está agrietado, mantén la rotura contenida y evita daños corporales durante la reparación pegando el vidrio con cinta adhesiva.
-
Coloca tiras superpuestas de cinta transparente de embalaje sobre la pantalla del iPad hasta cubrir toda la cara.
-
Haz tu mejor esfuerzo para seguir el resto de la guía como se describe. Sin embargo, una vez que se rompe el vidrio, es probable que continúe agrietándose a medida que trabajas, y es posible que necesites utilizar una herramienta de palanca de metal para sacar el cristal.
-
-
-
Coloca con cuidado una ventosa hasta la mitad del lado calentado.
-
Asegúrate de que la ventosa esté completamente plana en la pantalla para obtener un sello hermético.
-
Mientras sostienes el iPad hacia abajo con una mano, jala hacia arriba la ventosa para separar ligeramente el vidrio del panel frontal de la caja trasera.
-
-
-
Toma la primera púa que insertaste y deslízala hacia arriba en dirección a la esquina superior del iPad.
-
Si puedes ver la punta de la púa de apertura a través del vidrio frontal, no te asustes, simplemente tira de la púa un poco. Lo más probable es que todo esté bien, pero trata de evitar esto ya que puede depositar adhesivo en la parte frontal de la pantalla LCD que es difícil de limpiar.
-
-
-
Desliza la púa inferior izquierda a la esquina inferior izquierda para cortar el adhesivo en esa esquina.
-
Deja la púa en la esquina. No te entrometas más y no retires la púa del iPad.
-
Antenas
-
Cavidad del botón de inicio
-
Cable digitalizador
-
Los siguientes pasos le indicarán dónde debes hacer palanca para evitar daños en estos componentes. Sólo aplica calor y haz palanca donde se te indique.
-
-
-
La carcasa de la cámara frontal puede pegarse al panel frontal; despega la carcasa y colócala de nuevo sobre la cámara para protegerla.
-
Mueve la carcasa de la cámara hacia arriba en un borde para liberarla del adhesivo y retírala del panel frontal.
-
Vuelve a colocar la carcasa de la cámara frontal delante en su hueco en la carcasa trasera.
-
-
-
Usa pinzas para despegar y remover la pieza rectangular de cinta de pieza de espuma que cubre los tornillos del LCD.
-
Remueve la cubierta triangular de cinta que cubre los tornillos del LCD.
-
-
-
-
Remueve los siguientes tornillos que aseguran la placa de protección del LCD a la carcasa trasera del iPad:
-
Dos Phillips #00 de 2.6 mm
-
Trece Phillips #00 de 1.7 mm
-
Uno adicional Phillips #00 de 1.7 mm en algunos dispositivos.
-
-
-
Remueve los tres tornillos Phillips #00 de 1.3 mm que aseguran la protección del conector a la tarjeta lógica.
-
-
-
Usa una herramienta de apertura de plástico para hacer palanca en el conector del LCD de su socket en la tarjeta lógica.
-
-
-
Para minimizar la fuerza en el socket, intenta hacer palanca debajo del borde pequeño en el conector, en vez de en el borde largo el cual es mostrado en estas imágenes.
-
Gentilmente haz palanca en el conector digitalizador de su socket en la tarjeta lógica.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Reheat the iOpener in the microwave for one minute.
-
Place the heated iOpener on the back of the iPad, along the center. Let it sit there for 90 seconds to soften the battery adhesive.
-
Move the iOpener to the right of the back of the iPad (the side opposite the rear-facing camera), and let the iOpener sit for another 90 seconds.
-
If the iOpener cools significantly between sittings, reheat it for another minute.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Plastic Cards$2.99-
Flip the iPad back over and insert a plastic card between the top left battery and the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Press the card in further, breaking as much of the adhesive holding in the battery as you can.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the plastic card and reinsert it underneath the top right corner of the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Again, press the card in further, to break more of the adhesive behind the battery.
-
Leave this card in place to prevent the adhesive from resetting.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a second plastic card beneath the bottom left corner of the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slowly push the card in further, breaking more of the adhesive between the battery and the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the card and reinsert it, beneath the bottom right corner of the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasp both cards and slowly pull the right side of the battery up about two inches from the rear case.
-
Peel slowly and try to keep the battery as straight as possible.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
While lifting the right side of the battery up with one hand, use a plastic card to cut any adhesive still holding the battery down to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to peel up and remove the small piece of tape covering the front-facing camera cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to gently pry the lower metal plate up from the front-facing camera cable connector.
-
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the front-facing camera cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the second (upper) metal plate up from the front-facing camera cable connector.
-
Again, carefully pry the plate up and away from the front-facing camera cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to pry the front-facing camera cable's connector up from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently fold the front-facing camera cable up and out of the way of the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to peel up and remove the small piece of tape covering the headphone jack cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to gently pry the lower metal plate up from the headphone jack cable connector.
-
Being careful not to break the plate or the tape attached to it, pry it up and fold it away from the headphone jack cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry the second (upper) metal plate up from the front-facing camera cable connector.
-
Again, carefully pry the plate up and away from the headphone jack cable connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to pry the headphone jack cable's connector up out of its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to pry the rear-facing camera cable up from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to peel up and remove the small piece of tape covering the button ribbon cable ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to lift up the tab on the button ribbon cable ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to pull the button ribbon cable straight out of its ZIF socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently peel back the wide piece of tape covering the top of the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue peeling the tape, and remove it from the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to disconnect the two bottom antenna cable connectors from their sockets on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to peel back the small piece of tape covering both antenna cables on the bottom right side of the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With the tip of a spudger, peel up the larger piece of tape covering both antenna cables near the bottom of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the small metal retaining clip off the left antenna cable, then de-route the cable from the clip.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route the antenna cable from the corner of the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to remove the small piece of tape securing the antenna cable in the bottom right corner of the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.
-
Gently pull the antenna cable out of the way as you work along the piece of tape, to keep it from resealing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the antenna cable from the slot behind the Lightning connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to remove the small plastic cover on top of the horizontal screw on the right side of the Lightning connector housing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the plastic covering from the left side of the Lightning connector housing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the wide tape toward the top of the iPad, applying constant force to release it from the antenna cable between it and the speaker.
-
Slide the tip of a spudger through the gap between the wide tape and the antenna cable, breaking the adhesive connecting the two.
-
Continue pulling the wide tape until it is no longer covering the antenna cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the antenna cable tape up from the rear case of the iPad.
-
Gently pull the antenna cable out of the way as you work along the piece of tape, to keep it from resealing.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following three screws securing the bottom left antenna to the rear case:
-
One 1.2 mm Phillips #00 screw.
-
One 1.1 mm Phillips #00 screw.
-
One 2.5 mm Phillips #00 screw.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to loosen the foam adhesive securing the lower left antenna to the left speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws:
-
One 2.5 mm Phillips #00
-
Two 1.1 mm Phillips #00
-
One 1.2 mm Phillips #00
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to loosen the foam adhesive holding the antenna to the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 1.4 mm #00 Phillips screws securing the left and right speakers to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of a spudger into the gap between the left speaker and the bottom left side of the rear case.
-
Pry around the bottom of the speaker, sliding it out from its recess in the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Once enough of the speaker is exposed, grasp it and pull it away from its recess in the rear case.
-
Remove the left speaker from the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to slide the right speaker slightly toward the outside of the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of a spudger into the gap between the right speaker and the bottom right corner of the case.
-
Pry the speaker out from its recess in the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Once enough of the speaker is exposed, grasp it and pull it away from its slot in the rear case.
-
Remove the right speaker from the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove two 2.8 mm Phillips #00 screws from the base of the Lightning connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Reheat the iOpener in the microwave for one minute.
-
Place the heated iOpener on the left side of the back of the iPad. Let it sit there for 90 seconds to soften the logic board adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the flat end of a spudger underneath the Lightning port cable, freeing it from the adhesive securing it to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to carefully slide the spudger under the Lightning port cable nearest the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently insert the flat end of a spudger underneath the logic board nearest the front-facing camera. Slowly pry to free the corner from adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger underneath the center of the logic board. Slowly pry to free the section from adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the spudger underneath the logic board nearest the Lightning port cable and pry to free the corner.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the spudger further under the logic board and slide along its length to detach the last of the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the end of the logic board nearest the front-facing camera to ensure it is free of adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board and Lightning cable assembly up and pull toward the top of the iPad to remove the Lightning connector from its housing.
-
Cancelar: No complete esta guía.
31 personas más completaron esta guía.
Un comentario
Great guide! But on step 82 there is a plate that covers the plug, and the guide is missing a step to remove the plate.