Introducción
Prereq utilizado con iOpener
Qué necesitas
-
-
Si el vidrio de tu pantalla está agrietado, mantén la rotura contenida y evita daños corporales durante la reparación pegando el vidrio con cinta adhesiva.
-
Coloca tiras superpuestas de cinta transparente de embalaje sobre la pantalla del iPad hasta cubrir toda la cara.
-
Haz tu mejor esfuerzo para seguir el resto de la guía como se describe. Sin embargo, una vez que se rompe el vidrio, es probable que continúe agrietándose a medida que trabajas, y es posible que necesites utilizar una herramienta de palanca de metal para sacar el cristal.
-
-
-
Manipulándolo por la pestaña, coloca el iOpener calentado en el lateral del iPad a la izquierda del ensamblaje del botón de inicio.
-
Deja que el iOpener repose durante aproximadamente cinco minutos para ablandar el adhesivo debajo del vidrio.
-
-
-
Coloca con cuidado una ventosa hasta la mitad del lado calentado.
-
Asegúrate de que la ventosa esté completamente plana en la pantalla para obtener un sello hermético.
-
Mientras sostienes el iPad hacia abajo con una mano, jala hacia arriba la ventosa para separar ligeramente el vidrio del panel frontal de la caja trasera.
This step is totally pointless if you have a shattered screen. The suction cup is rendered useless. Any tips on what to do if you can't get any suction due to a shattered screen?
just pick out the glass shards if it is cracked that bad you are better off scrapping the digitizer
-
-
-
Mientras sostienes el vidrio con la ventosa, desliza la punta de una púa de apertura en el espacio entre el vidrio y el cuerpo del iPad.
-
Tira de la protuberancia de plástico de la ventosa para liberar el sello de vacío y retira la ventosa del ensamblaje de la pantalla.
thanks jfaulks1 (I did not copy and paste lol)
-
-
-
Toma la primera púa que insertaste y deslízala hacia arriba en dirección a la esquina superior del iPad.
-
Si puedes ver la punta de la púa de apertura a través del vidrio frontal, no te asustes, simplemente tira de la púa un poco. Lo más probable es que todo esté bien, pero trata de evitar esto ya que puede depositar adhesivo en la parte frontal de la pantalla LCD que es difícil de limpiar.
-
-
-
-
Desliza la púa de apertura alrededor de la esquina superior izquierda del iPad para separar el adhesivo.
Gezz this is though! Cracked the glass while replacing it.
:( sad (rip glass lol)
-
-
-
Inserta la púa anterior más profundamente en el iPad y deslízala lejos de la cámara hacia la esquina.
Shattered my screen pretty bad here, making it so that whenever I continued to move the pick the glass separated and I couldn’t continue moving it. Be VERY gentle moving the pick; almost no force is required.
-
-
-
Desliza la púa inferior izquierda a la esquina inferior izquierda para cortar el adhesivo en esa esquina.
-
Deja la púa en la esquina. No te entrometas más y no retires la púa del iPad.
-
Antenas
-
Cavidad del botón de inicio
-
Cable digitalizador
-
Los siguientes pasos le indicarán dónde debes hacer palanca para evitar daños en estos componentes. Sólo aplica calor y haz palanca donde se te indique.
-
-
-
Levanta lentamente y con cuidado para separar aún más el adhesivo a lo largo del borde inferior.
Really, add a few more pics and a few more picks, see how long and difficult you can make this guide. 26 steps to get the top screen off is ridiculous.
-
-
-
Una vez separado todo el adhesivo, abre el cristal frontal como si fuera una página de un libro y apóyalo en tu espacio de trabajo.
I recommend wearing latex gloves or be sure not to put too many finger prints on the front or back of this front glass when lifting it or completing the remainder of the steps. I made this mistake and upon installing the new LCD and putting the iPad back together I realized that I left a few finger prints on the inside of the front glass. After re-securing the adhesive strips putting the iPad back together there are now unremovable fingerprints visible when the LCD is turned off. Just a recommendation on the gloves or be sure to wipe both sides of the front glass clean before putting all back together.
-
-
-
La carcasa de la cámara frontal puede pegarse al panel frontal; despega la carcasa y colócala de nuevo sobre la cámara para protegerla.
-
Mueve la carcasa de la cámara hacia arriba en un borde para liberarla del adhesivo y retírala del panel frontal.
-
Vuelve a colocar la carcasa de la cámara frontal delante en su hueco en la carcasa trasera.
-
Para volver a armar tu dispositivo, sigue estas instrucciones en orden reverso.
Para volver a armar tu dispositivo, sigue estas instrucciones en orden reverso.
Cancelar: No complete esta guía.
Una persona más ha completado esta guía.
Un agradecimiento especial a estos traductores:
100%
Estos traductores nos están ayudando a reparar el mundo! ¿Quieres contribuir?
Empezar a traducir ›
In case of broken glass, here are some hints:
- I prefer 3M "3350" tape; a metalized polypropylene tape with an acrylic adhesive. It's a very thin, silvery HVAC tape, not your standard duct tape.
- Test your tape to make sure it sticks really well to the glass.
- Use isopropyl alcohol on a paper towel to remove fingerprints and other dirt to help the tape stick to the screen.
- Use the widest tape you can find, and apply it evenly, without trapping bubbles, without crinkles: This greatly improves your chance of success with the suction cup later.
- Cut tape pieces long enough and go over the (rounded) edge; afterwards carefully run a scalpel alongside the edge (between bezel and glass) to trim off any excess.
- Don't overlap edges of the tape: butt-join them instead.
- If needed: repeat in other direction.
- If needed: Cut square piece of tape (size of suction cup) and place it where you want to lift the glass, so that the suction cup doesn't cover any butt-joins.
Good luck, you brave person!
volty - Contestar
This is the second broken screen I’ve fixed. Overlapped package tape carefully stuck to the glass and trimmed to the edges will contain most of the shards. I found that a hair dryer works for softening the glue. After getting under an edge with the suction cup I carefully followed the opening sequence using a combination of plastic picks and a single edge razor blade to get under the small pieces. It was slow going with lots of reheating with the dryer (about 45 minutes), but the taped glass came off without glass everywhere.
Bill Roughen - Contestar