Repara tus cosas

Derecho a reparar

Partes y herramientas

iPad 6 Wi-Fi Front Panel Assembly Replacement

Escrito Por: Sam Goldheart (y otro participante)
  • Comentarios: 0
  • Favoritos: 0

Dificultad

Difícil

Pasos

5

Tiempo Requerido

1 - 2 horas

Secciones

1

Banderas

1

Prerequisite Only

Sólo Prerrequisito

Por favor, ten en cuenta que esta guía es sólo un prerrequisito para otras guías.

Introducción

This is a prerequisite only guide for the front panel replacement.

Herramientas

Comprar estas herramientas

Partes

No se especificaron partes.

  1. Remove any tape covering the home button ribbon cable connector. Remove any tape covering the home button ribbon cable connector.

    • Remove any tape covering the home button ribbon cable connector.

    Traducir

  2. Use the flat end of a spudger to flip the tab on the home button ribbon cable ZIF connector upward. Carefully pull the home button ribbon cable straight out of the ZIF connector. Carefully pull the home button ribbon cable straight out of the ZIF connector.

    • Use the flat end of a spudger to flip the tab on the home button ribbon cable ZIF connector upward.

    • Carefully pull the home button ribbon cable straight out of the ZIF connector.

    Traducir

  3. Kits de Reparación de Pantalla LCD de iPhone

    La opción de presupuesto, cubierta por nuestra garantía de por vida.

    Compra kits

    Kits de Reparación de Pantalla LCD de iPhone

    Reduce los costos de reparación, no la calidad.

    Compra kits

  4. Use a the flat end of a spudger or a fingernail to carefully pop the two digitizer cable connectors straight up from their sockets. To avoid damaging your iPad, pry only on the connectors themselves, not on the socket on the logic board. To avoid damaging your iPad, pry only on the connectors themselves, not on the socket on the logic board.

    • Use a the flat end of a spudger or a fingernail to carefully pop the two digitizer cable connectors straight up from their sockets.

    • To avoid damaging your iPad, pry only on the connectors themselves, not on the socket on the logic board.

    Traducir

  5. Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case. Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case.

    • Carefully peel the home button ribbon cable up off of the adhesive holding it to the rear case.

    Traducir

  6. Remove the front panel assembly. If you experience "ghost" or "phantom" touch input issues with your new display, this can be resolved by adding a layer of very thin insulating tape, such as Kapton (polyimide) tape, to the highlighted areas on the back of the panel. iFixit panels come with the proper insulation, and should not require the addition of any tape.
    Herramienta utilizada en este paso:
    Polyimide Tape
    $9.99

    • Remove the front panel assembly.

    • If you experience "ghost" or "phantom" touch input issues with your new display, this can be resolved by adding a layer of very thin insulating tape, such as Kapton (polyimide) tape, to the highlighted areas on the back of the panel. iFixit panels come with the proper insulation, and should not require the addition of any tape.

    • Without the proper insulation, these areas of the digitizer can ground out against other components, causing touch input malfunction.

    • The insulation is not visible to the naked eye, and is different from the foam dust barrier strips found on many iPads.

    Traducir
Conclusión

To reassemble your device, follow these instructions in reverse order.

Autor

con 1 otro colaborador

Sam Goldheart

Miembro Desde 18/10/12

400,928 Reputación

547 Guías creadas

Insignias: 48

+ 45 más insignias

Equipo

iFixit Miembro de iFixit

Community

111 Miembros

10,650 Guías creadas

0 comentarios

Agregar un comentario

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 37