Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
-
Si tu cristal de pantalla está agrietado, mantén una mayor rotura contenida y evita daños corporales durante su reparación pegando el vidrio.
-
Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPad hasta que toda la cara está cubierta.
-
Haz lo que puedas para seguir el resto de la guía según lo descrito. Sin embargo, una vez que el vidrio se rompe, es probable que continúe agrietándose mientras trabajas, y puede que tengas que usar una herramienta metálica para sacar el vidrio.
-
-
-
Hay una pequeña brecha en el anillo adhesivo del iPad en la esquina superior derecha del iPad, aproximadamente 2,0 pulgadas (~ 5 cm) desde la parte superior del iPad. Vas a explotar esta debilidad.
-
Alinea la herramienta con el botón de silencio. Inserta la punta de una herramienta de apertura de plástico en el hueco entre el cristal frontal y el bisel de plástico. Basta con insertar la punta de la herramienta de apertura, lo suficiente como para ensanchar la grieta.
-
-
-
Una vez que haya pasado la antena Wi-FI (aproximadamente 75 mm desde el borde derecho, o justo al lado del botón de inicio) vuelva a insertar la selección de apertura a su profundidad máxima.
-
Desliza la palanca hacia la derecha, liberando el adhesivo que sujeta la antena Wi-Fi al cristal frontal.
-
La antena está conectada a la parte inferior del iPad a través de tornillos y un cable. Este paso separa la antena del panel frontal, asegurando que al retirar el panel, la antena no se dañará.
-
-
-
Desliza la púa de apertura a lo largo del borde superior del iPad, tirando ligeramente hacia fuera para rodear el soporte frontal de la cámara.
-
El adhesivo a lo largo de esta sección es muy grueso, y puede requerirse una cantidad justa de fuerza. Trabaja con cuidado y lentamente, asegurándose de no resbalar y dañarse a sí mismo o a tu iPad.
-
-
-
-
Desliza la púa de apertura a lo largo del borde izquierdo del iPad, liberando el adhesivo a medida que avanza. El adhesivo es delgado debido al digitalizador a lo largo de todo el lado izquierdo. Asegúrate de que la púa no esté más de 10 mm dentro para evitar dañar el digitalizador.
-
-
Herramienta utilizada en este paso:Microfiber Cleaning Cloths$3.99
-
Sosteniendo el iPad por las esquinas superior e inferior derecha, gira el cristal delantero lejos del iPad.
-
Durante el montaje, utiliza un paño de microfibra y aire comprimido para limpiar el polvo o las huellas dactilares de la pantalla LCD antes de volver a instalar el cristal.
-
-
-
Retire los cuatro tornillos Phillips # 00 de 2 mm que sujetan la pantalla LCD al marco de aluminio.
-
-
-
Utilizando la punta de un spudger, retire el trozo de cinta que cubre el conector del cable de cinta LCD.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use tweezers to peel back and remove the piece of electrical tape covering the headphone jack assembly cable connector.
-
Using the tip of a spudger, flip up the retaining flap on both of the ZIF connectors securing the headphone jack cable to the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the flat end of a spudger underneath the headphone jack assembly cable, releasing the adhesive securing it to the rear aluminum frame.
-
Pull the headphone jack assembly cable straight out of its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully move, but do not remove the front-facing camera ribbon cable aside with the flat edge of a spudger.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back and remove the adhesive tape covering the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of the spudger underneath the microphone ribbon cable and carefully push it out from its socket on the ZIF connector.
-
Use the flat edge of a spudger to move the microphone ribbon cable aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Push the volume button ribbon cable from its ZIF connector.
-
Gently bend the volume button ribbon cable upwards to move it aside.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws from the headphone jack assembly:
-
Five 2.6 mm Phillips #0
-
Two 2.2 mm Wide Head Phillips #00
-
Two 2.6 mm Phillips #00
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly upwards towards the top of the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws securing the power & volume button cable to the aluminum frame:
-
Two 5.5 mm Phillips #0
-
One 2.6 mm Phillips #0
-
Two 2.6 mm Phillips #0
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the piece of plastic covering the volume buttons.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.
-
Move the plastic opening tool around the sensor, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the tip of a spudger underneath the power & volume cables, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.
-
Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.
-
With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift and remove the power & volume button cable out of the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Wedge the tip of the plastic opening tool underneath the top side of the power button.
-
Pry the topside of the power button up off the power button bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Repeat the previous step on the underside of the power button.
-
Lift and remove the power button bracket from the power & volume button assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Wedge the tip of the plastic opening tool underneath the top side of the rotation lock/mute switch.
-
Slide the plastic opening tool downwards to pry the topside of the rotation lock/mute switch from its bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of the plastic opening tool underneath the top volume rocker and pry upwards to separate it from the volume buttons bracket.
-
Repeat the procedure to separate the bottom volume rocker from the volume buttons bracket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift and remove the power & volume button ribbon cable.
-
Cancelar: No complete esta guía.
9 personas más completaron esta guía.