Saltar al contenido principal

Introducción

Internal prereq.

  1. Carefully move, but do not remove the front-facing camera ribbon cable aside with the flat edge of a spudger.
    • Carefully move, but do not remove the front-facing camera ribbon cable aside with the flat edge of a spudger.

    OR, if you’re having a problem with the front camera OR the ambient light sensor (which is the small module above the camera lens), go ahead and remove the front camera and swap in a new one, complete with sensor module. It is theoretically possible to remove and swap just the ambient light sensor module, but this author found it too difficult to be worth it, if it’s possible at all.

    [The ambient light sensor makes automatic adjustment of screen brightness possible, if you switch it on with the toggle under “screen and brightness” in settings. When working, the screen gets dimmer in dim settings and brighter in bright settings. It might sound unimportant, but if you’ve tried to take pictures in bright sunlight with a dim screen…you’ll appreciate it’s usefulness.]

    Bonnie Baxter - Contestar

  2. Peel back and remove the adhesive tape covering the headphone jack assembly. Peel back and remove the adhesive tape covering the headphone jack assembly.
    • Peel back and remove the adhesive tape covering the headphone jack assembly.

  3. Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.
    • Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.

  4. Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now

    Kits de Reparación de Batería de iPhone

    Sólo $29.99

    Buy Now
  5. Insert the tip of the spudger underneath the microphone ribbon cable and carefully push it out from its socket on the ZIF connector. Use the flat edge of a spudger to move the microphone ribbon cable aside.
    • Insert the tip of the spudger underneath the microphone ribbon cable and carefully push it out from its socket on the ZIF connector.

    • Use the flat edge of a spudger to move the microphone ribbon cable aside.

  6. Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
    • Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.

  7. Push the volume button ribbon cable from its ZIF connector. Gently bend the volume button ribbon cable upwards to move it aside.
    • Push the volume button ribbon cable from its ZIF connector.

    • Gently bend the volume button ribbon cable upwards to move it aside.

  8. Remove the following screws from the headphone jack assembly: Five 2.6 mm Phillips #0 Two 2.2 mm Wide Head Phillips #00
    • Remove the following screws from the headphone jack assembly:

    • Five 2.6 mm Phillips #0

    • Two 2.2 mm Wide Head Phillips #00

    • Two 2.6 mm Phillips #00

    • These screws are angled into the aluminum frame. Be sure to hold the screwdriver so that the screwdriver is in line with the screw, to avoid stripping the screw.

  9. Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly upwards towards the top of the device.
    • Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly upwards towards the top of the device.

  10. Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught. Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught.
    • Grasping the headphone jack assembly with one hand, pull the assembly from the iPad, minding any cables that may get caught.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Agregar Comentario

Ver Estadísticas:

Ultimas 24 Horas: 0

Últimos 7 Días: 0

Últimos 30 Días: 0

Todo El Tiempo: 15