Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Calienta el iOpener durante treinta segundos.
-
Dependiendo de la potencia de tu microondas, puede necesitar más o menos tiempo. El iOpener está suficientemente caliente cuando apenas está demasiado caliente al tacto.
-
A lo largo del procedimiento de reparación, en cuanto el iOpener se enfríe, vuelve a calentarlo en el microondas treinta segundos más cada vez.
-
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
-
Si tu cristal de pantalla está agrietado, mantén una mayor rotura contenida y evita daños corporales durante su reparación pegando el vidrio.
-
Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPad hasta que toda la cara está cubierta.
-
Haz lo que puedas para seguir el resto de la guía según lo descrito. Sin embargo, una vez que el vidrio se rompe, es probable que continúe agrietándose mientras trabajas, y puede que tengas que usar una herramienta metálica para sacar el vidrio.
-
-
-
Hay una pequeña brecha en el anillo adhesivo del iPad en la esquina superior derecha del iPad, aproximadamente 2,0 pulgadas (~ 5 cm) desde la parte superior del iPad. Vas a explotar esta debilidad.
-
Alinea la herramienta con el botón de silencio. Inserta la punta de una herramienta de apertura de plástico en el hueco entre el cristal frontal y el bisel de plástico. Basta con insertar la punta de la herramienta de apertura, lo suficiente como para ensanchar la grieta.
-
-
-
Una vez que haya pasado la antena Wi-FI (aproximadamente 75 mm desde el borde derecho, o justo al lado del botón de inicio) vuelva a insertar la selección de apertura a su profundidad máxima.
-
Desliza la palanca hacia la derecha, liberando el adhesivo que sujeta la antena Wi-Fi al cristal frontal.
-
La antena está conectada a la parte inferior del iPad a través de tornillos y un cable. Este paso separa la antena del panel frontal, asegurando que al retirar el panel, la antena no se dañará.
-
-
-
-
Desliza la púa de apertura a lo largo del borde superior del iPad, tirando ligeramente hacia fuera para rodear el soporte frontal de la cámara.
-
El adhesivo a lo largo de esta sección es muy grueso, y puede requerirse una cantidad justa de fuerza. Trabaja con cuidado y lentamente, asegurándose de no resbalar y dañarse a sí mismo o a tu iPad.
-
-
-
Desliza la púa de apertura a lo largo del borde izquierdo del iPad, liberando el adhesivo a medida que avanza. El adhesivo es delgado debido al digitalizador a lo largo de todo el lado izquierdo. Asegúrate de que la púa no esté más de 10 mm dentro para evitar dañar el digitalizador.
-
-
Herramienta utilizada en este paso:Microfiber Cleaning Cloths$3.99
-
Sosteniendo el iPad por las esquinas superior e inferior derecha, gira el cristal delantero lejos del iPad.
-
Durante el montaje, utiliza un paño de microfibra y aire comprimido para limpiar el polvo o las huellas dactilares de la pantalla LCD antes de volver a instalar el cristal.
-
-
-
Retira los cuatro tornillos Phillips #00 de 2 mm que sujetan la pantalla LCD al marco de aluminio.
-
-
-
Usando la punta de un spudger, despega el trozo de cinta que cubre el conector del cable plano LCD.
-
-
-
Levanta la tapa de retención de los dos conectores ZIF del cable plano digitalizador.
-
-
-
Despega y retira el trozo de cinta aislante que cubre el conector del cable de la toma de auriculares.
-
Con la punta de un spudger, levante la solapa de retención de ambos conectores ZIF que fijan el cable de la toma de auriculares a la placa lógica.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back and remove the adhesive tape covering the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, pry the front-facing camera connector off of its socket on the headphone jack assembly.
-
Slide the spudger to the right, releasing the adhesive holding down the camera cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the tip of a spudger, flip up the retaining flap on the microphone cable ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the tip of the spudger underneath the microphone ribbon cable, removing it from its ZIF connector.
-
Slide the spudger to the left, releasing the adhesive holding the microphone ribbon cable to the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
-
Remove the volume button ribbon cable from its ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws from the headphone jack assembly:
-
Five 2.6 mm Phillips #0
-
Two 2.0 mm Wide Head Phillips #00
-
Two 2.6 mm Phillips #00
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently peel the headphone jack assembly ribbon cable up from the foam pad in the top left of the rear case.
-
If necessary, use the flat end of a spudger to loosen the adhesive securing the ribbon cable to the foam.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasping the headphone jack assembly with both hands, pull the assembly from the iPad, minding any cables that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws securing the power & volume button cable to the aluminum frame:
-
Two 5.5mm Phillips #0
-
One 2.6 mm Phillips #0
-
Two 2.6 mm Phillips #0
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the piece of plastic covering the volume buttons.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.
-
Move the plastic opening tool around the sensor, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue sliding the plastic opening tool underneath the power & volume cables, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the tip of a spudger, release the adhesive underneath the volume button branch of the ribbon cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.
-
Lift and remove the power & volume button cable out of the rear aluminum case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the spudger to help guide it out of the iPad, push the mute/lock switch out of its recess in the aluminum frame.
-
Lift and remove the mute/lock switch out of the rear aluminum case.
-
Un comentario
I just got finished with replacing the power/mute/volume assembly in a wifi ipad 3, and I did not find that removing the headphone jack assembly was necessary. Just unscrew the rear camera so you can pivot it out of the way of the power switch, but it can stay connected via its ribbon cable.
Also, when reassembling I found that I needed to be careful about over-tightening the screws around all three buttons. If they were too tight they wouldn't click properly.