Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a SIM eject tool or an uncoiled paperclip to eject the SIM tray.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the SIM tray out of its slot and remove it from the iPad.
-
-
-
Si tu cristal de pantalla está agrietado, mantén una mayor rotura contenida y evita daños corporales durante su reparación pegando el vidrio.
-
Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPad hasta que toda la cara está cubierta.
-
Haz lo que puedas para seguir el resto de la guía según lo descrito. Sin embargo, una vez que el vidrio se rompe, es probable que continúe agrietándose mientras trabajas, y puede que tengas que usar una herramienta metálica para sacar el vidrio.
-
-
-
Hay una pequeña brecha en el anillo adhesivo del iPad en la esquina superior derecha del iPad, aproximadamente 2,0 pulgadas (~ 5 cm) desde la parte superior del iPad. Vas a explotar esta debilidad.
-
Alinea la herramienta con el botón de silencio. Inserta la punta de una herramienta de apertura de plástico en el hueco entre el cristal frontal y el bisel de plástico. Basta con insertar la punta de la herramienta de apertura, lo suficiente como para ensanchar la grieta.
-
-
-
Una vez que haya pasado la antena Wi-FI (aproximadamente 75 mm desde el borde derecho, o justo al lado del botón de inicio) vuelva a insertar la selección de apertura a su profundidad máxima.
-
Desliza la palanca hacia la derecha, liberando el adhesivo que sujeta la antena Wi-Fi al cristal frontal.
-
La antena está conectada a la parte inferior del iPad a través de tornillos y un cable. Este paso separa la antena del panel frontal, asegurando que al retirar el panel, la antena no se dañará.
-
-
-
-
Desliza la púa de apertura a lo largo del borde superior del iPad, tirando ligeramente hacia fuera para rodear el soporte frontal de la cámara.
-
El adhesivo a lo largo de esta sección es muy grueso, y puede requerirse una cantidad justa de fuerza. Trabaja con cuidado y lentamente, asegurándose de no resbalar y dañarse a sí mismo o a tu iPad.
-
-
-
Desliza la púa de apertura a lo largo del borde izquierdo del iPad, liberando el adhesivo a medida que avanza. El adhesivo es delgado debido al digitalizador a lo largo de todo el lado izquierdo. Asegúrate de que la púa no esté más de 10 mm dentro para evitar dañar el digitalizador.
-
-
Herramienta utilizada en este paso:Microfiber Cleaning Cloths$3.99
-
Sosteniendo el iPad por las esquinas superior e inferior derecha, gira el cristal delantero lejos del iPad.
-
Durante el montaje, utiliza un paño de microfibra y aire comprimido para limpiar el polvo o las huellas dactilares de la pantalla LCD antes de volver a instalar el cristal.
-
-
-
Retire los cuatro tornillos Phillips # 00 de 2 mm que sujetan la pantalla LCD al marco de aluminio.
-
-
-
Con la punta de un spudger, retire la pieza de cinta que cubre el conector del cable de cinta LCD.
-
-
-
Con la punta de un spudger, despegue la pieza de cinta que fija el cable plano de la pantalla táctil a la placa lógica.
-
-
-
Despega y retira el trozo de cinta eléctrica que cubre el conector para audífonos.
-
Con la punta de un spudger, levanta la tapa de retención de los dos conectores ZIF que sujetan el cable del conector para audífonos a la placa lógica.
-
-
-
Despega y retira el trozo de cinta que cubre el conector ZIF del cable de la tarjeta SIM.
-
Levanta la tapa de retención del conector ZIF del cable de la tarjeta SIM.
-
Con la punta de un spudger, saca el cable de la tarjeta SIM de su zócalo en la placa lógica.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 1.75 mm Phillips #00 screws securing the SIM board to the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding the headphone jack assembly cable out of the way, remove the SIM board from the iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back and remove the adhesive tape covering the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.6 mm Phillips #0 screw securing the camera cable to the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the flat end of a spudger, pry the front-facing camera off of its socket on the headphone jack assembly.
-
Without removing the spudger, slide the spudger to the right, releasing the adhesive holding down the camera cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using the tip of the spudger, flip up the retaining flap on the microphone cable ZIF connector.
-
Insert the tip of the spudger underneath the microphone ribbon cable, removing it from its ZIF connector.
-
Slide the spudger to the left, releasing the adhesive holding the microphone ribbon cable to the headphone jack assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of the spudger to pry up the antenna connector cable out of its socket on the headphone jack assembly board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip up the retaining flap securing the volume/power button ribbon cable connector to the headphone jack assembly board.
-
Remove the volume button ribbon cable from its ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws from the headphone jack assembly:
-
Five 2.6 mm Phillips #0
-
Two 2.2 mm Wide Head Phillips #00
-
Two 2.6 mm Phillips #00
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding onto the ribbon cable of the headphone jack assembly, carefully pull the assembly parallel to the iPad, toward the bottom of the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Grasping the headphone jack assembly with both hands, pull the assembly from the iPad, minding any cables that may get caught.
-
-
-
Desconecta los siguientes conectores de sus respectivos zócalos en la placa lógica:
-
Cable de la antena de Wi-Fi
-
Cable del conector del altavoz.
-
Cable del conector del dock.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the seven screws securing the logic board to the rear aluminum panel.
-
Six 2.1mm Phillips #00
-
One 2.5mm Phillips #00
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip the logic board over, minding any cables that may get caught.
-
Using the tip of a spudger, remove the three antenna connectors from their sockets on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of the iSesamo or the edge of a plastic opening tool to remove the metal EMI tape covering the antenna cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 1.75 mm Phillips #00 screws securing the antenna to the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using your fingers or a spudger, lift the antenna out of its socket, rotating it toward the bottom of the device.
-
Make sure that the orange ribbon cable passes completely through its hole in the aluminum frame.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger underneath the adhesive tape securing the antenna cable to the aluminum frame.
-
Slide the cable to the left, releasing the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Holding the antenna cable firmly in your fingers, pull the cable off of the aluminum frame.
-
Minding any cables that may get caught, remove the antenna from the iPad.
-
Cancelar: No complete esta guía.
6 personas más completaron esta guía.
3 comentarios
During step 46 near your left hand. What is the part that fits right next to the front facing camera? It is a plastic housing that accidentally got pulled out and there is a small flex connector behind it. Can you tell me what I broke? I think it may be a bluetooth antenna. Thanks
My email is
Does it make a difference what order the antena connectors are connected? There are three, but it is not clear which connector is for which antenna. There are three antenna including the GPS. Do they simply connect left to right? Or is there a specific place for each?
did you find answer, about order that 3 antennas cable