Saltar al contenido principal

Esta guía ha sufrido modificaciones. Revisa la última versión sin revisar.

iPad 3 4G Power & Volume Button Assembly Replacement

Sólo Prerrequisito
Esta guía solo debería usarse como prerrequisito para otras guías. Por tanto, estará incompleta.

Qué necesitas

  1. iPad 3 4G Power & Volume Button Assembly Replacement, Power & Volume Button Assembly: paso 1, imagen 1 de 1
    • Remove the following screws securing the power & volume button cable to the aluminum frame:

    • Two 5.5 mm Phillips #0

    • One 2.6 mm Phillips #0

    • Two 2.6 mm Phillips #0

    • The two screws located on top are angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

  2. iPad 3 4G Power & Volume Button Assembly Replacement: paso 2, imagen 1 de 1
    • Remove the piece of plastic covering the volume buttons.

  3. iPad 3 4G Power & Volume Button Assembly Replacement: paso 3, imagen 1 de 1
    • Remove the single 2.6 mm Phillips #00 screw holding the volume button frame to the aluminum frame.

    • This screw is angled into the aluminum frame. Be sure to always hold the screwdriver in line with the screw.

  4. iPad 3 4G Power & Volume Button Assembly Replacement: paso 4, imagen 1 de 2 iPad 3 4G Power & Volume Button Assembly Replacement: paso 4, imagen 2 de 2
    • Wedge the edge of a plastic opening tool underneath the sleep/wake sensor, being careful to not damage the fragile cable.

    • Move the plastic opening tool around the sensor, releasing the adhesive.

  5. iPad 3 4G Power & Volume Button Assembly Replacement: paso 5, imagen 1 de 2 iPad 3 4G Power & Volume Button Assembly Replacement: paso 5, imagen 2 de 2
    • Slide a spudger underneath the power & volume cables, releasing the adhesive.

  6. iPad 3 4G Power & Volume Button Assembly Replacement: paso 6, imagen 1 de 2 iPad 3 4G Power & Volume Button Assembly Replacement: paso 6, imagen 2 de 2
    • Using the tip of the spudger rather that the wide edge, release the adhesive underneath the volume button branch of the ribbon cable.

  7. iPad 3 4G Power & Volume Button Assembly Replacement: paso 7, imagen 1 de 3 iPad 3 4G Power & Volume Button Assembly Replacement: paso 7, imagen 2 de 3 iPad 3 4G Power & Volume Button Assembly Replacement: paso 7, imagen 3 de 3
    • Continue sliding the tip of the spudger toward the top of the iPad, releasing the adhesive.

  8. iPad 3 4G Power & Volume Button Assembly Replacement: paso 8, imagen 1 de 2 iPad 3 4G Power & Volume Button Assembly Replacement: paso 8, imagen 2 de 2
    • With the tip of the spudger still underneath the ribbon cable, gently lift the power button out of its socket in the aluminum frame.

  9. iPad 3 4G Power & Volume Button Assembly Replacement: paso 9, imagen 1 de 2 iPad 3 4G Power & Volume Button Assembly Replacement: paso 9, imagen 2 de 2
    • Holding the power & volume button cable with with both hands, carefully pull the volume buttons and lock switch from their sockets in the aluminum frame.

    • Lift and remove the power & volume button cable out of the rear aluminum case.

Conclusión

To reassemble your device, follow these instructions in reverse order.

Brett Hartt

Miembro Desde 04/12/10

127,749 Reputación

143 Guías creadas

Equipo

iFixit Miembro de iFixit

Staff

136 Miembros

16,574 Guías creadas

0 comentarios

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 0

Ultimos 7 días: 0

Ultimos 30 días: 0

Todo El Tiempo: 129