Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
-
Si tu cristal de pantalla está agrietado, mantén una mayor rotura contenida y evita daños corporales durante su reparación pegando el vidrio.
-
Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPad hasta que toda la cara está cubierta.
-
Haz lo que puedas para seguir el resto de la guía según lo descrito. Sin embargo, una vez que el vidrio se rompe, es probable que continúe agrietándose mientras trabajas, y puede que tengas que usar una herramienta metálica para sacar el vidrio.
-
-
-
Hay una pequeña brecha en el anillo adhesivo del iPad en la esquina superior derecha del iPad, aproximadamente 2,0 pulgadas (~ 5 cm) desde la parte superior del iPad. Vas a explotar esta debilidad.
-
Alinea la herramienta con el botón de silencio. Inserta la punta de una herramienta de apertura de plástico en el hueco entre el cristal frontal y el bisel de plástico. Basta con insertar la punta de la herramienta de apertura, lo suficiente como para ensanchar la grieta.
-
-
-
Una vez que haya pasado la antena Wi-FI (aproximadamente 75 mm desde el borde derecho, o justo al lado del botón de inicio) vuelva a insertar la selección de apertura a su profundidad máxima.
-
Desliza la palanca hacia la derecha, liberando el adhesivo que sujeta la antena Wi-Fi al cristal frontal.
-
La antena está conectada a la parte inferior del iPad a través de tornillos y un cable. Este paso separa la antena del panel frontal, asegurando que al retirar el panel, la antena no se dañará.
-
-
-
Desliza la púa de apertura a lo largo del borde superior del iPad, tirando ligeramente hacia fuera para rodear el soporte frontal de la cámara.
-
El adhesivo a lo largo de esta sección es muy grueso, y puede requerirse una cantidad justa de fuerza. Trabaja con cuidado y lentamente, asegurándose de no resbalar y dañarse a sí mismo o a tu iPad.
-
-
-
Desliza la púa de apertura a lo largo del borde izquierdo del iPad, liberando el adhesivo a medida que avanza. El adhesivo es delgado debido al digitalizador a lo largo de todo el lado izquierdo. Asegúrate de que la púa no esté más de 10 mm dentro para evitar dañar el digitalizador.
-
-
-
Herramienta utilizada en este paso:Microfiber Cleaning Cloths$3.99
-
Sosteniendo el iPad por las esquinas superior e inferior derecha, gira el cristal delantero lejos del iPad.
-
Durante el montaje, utiliza un paño de microfibra y aire comprimido para limpiar el polvo o las huellas dactilares de la pantalla LCD antes de volver a instalar el cristal.
-
-
-
Retira los cuatro tornillos Phillips de 2,0 mm que sujetan la pantalla LCD a la carcasa trasera.
-
-
-
Utiliza el borde de una herramienta de apertura de plástico para levantar con cuidado las solapas de sujeción de las dos tomas ZIF del cable plano digitalizador.
-
-
-
Levanta la pantalla LCD por el borde largo más alejado del cable digitalizador y gírala suavemente hacia la carcasa trasera, como si estuvieras cerrando un libro.
-
Mientras mantienes levantada la pantalla LCD, desliza suavemente el panel frontal alejándolo del iPad. Ten cuidado de no enganchar el cable digitalizador en la carcasa trasera o en la pantalla LCD.
-
Vuelve a colocar la pantalla LCD en la carcasa para guardarla.
-
-
-
Levanta la pantalla LCD por el borde largo más cercano a los botones de volumen y sácala con cuidado de la carcasa trasera, como si pasaras la página de un libro.
-
Coloca la pantalla LCD boca abajo sobre una superficie limpia. Puedes apoyarla sobre un paño suave para evitar arañazos.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to lift the display data cable lock upwards.
-
Pull the display data cable out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the LCD assembly from the rear panel assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If present, remove the piece of tape on the dock connector cable with a plastic opening tool.
-
Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board.
-
Peel the dock connector ribbon cable off the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry the speaker cable connector straight up from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws:
-
Two 2.1 mm Phillips screws securing one of two metal brackets to the rear case.
-
One 2.6 mm Phillips screw securing the logic board to the rear case.
-
Remove the metal bracket from the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If present, use tweezers to remove the piece of tape covering the end of the headphone jack/control board cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to flip up the retaining flap on the headphone jack/control board cable ZIF socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the tip of a spudger underneath the headphone jack/control board ribbon cable to disconnect it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 2.1 mm Phillips screws securing the second metal bracket to the rear case near the digitizer cable socket.
-
Remove the metal bracket from the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of a plastic opening tool to gently pry the logic board up from the adhesive securing it to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board out from the rear case and flip it over toward the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the Wi-Fi antenna connector up from its socket on the logic board.
-
Remove the logic board from the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Reheat the iOpener in the microwave for one minute.
-
Place the heated iOpener on the back of the iPad just right of center (the side opposite the rear facing camera). Let it sit there for 90 seconds to soften the battery adhesive.
-
Move the iOpener to the center of the back of the iPad and let the iOpener sit for another 90 seconds.
-
Move the iOpener to the left edge (the side with the rear facing camera) of the back of the iPad and let the iOpener sit for another 90 seconds.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Plastic Cards$2.99-
Flip the iPad back over and insert a plastic card between the bottom battery cell and the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Starting with the battery cell closest to the dock connector, run a plastic opening tool underneath the edge of the battery closest to the logic board void to make enough room to insert a plastic card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the card at the case side corner and slide inward to separate more adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Work the card around the corner and insert along the case-side of the cell.
-
Insert the card at as shallow an angle as you can manage to avoid bending the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the card at the bottom corner (closest to the headphone jack) to free this side of the battery cell.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the card along the side of the cell to detach any remaining adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the end of the battery cell away from the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the corner of the battery off of the case to begin freeing the final side of the dock side cell.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry up the remaining corner of the cell. Avoid bending the cable connecting the battery cells.
-
Leave this card in place to prevent the adhesive from resetting while you loosen the other battery cells.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
On the battery cell nearest the headphone jack, run a second plastic card underneath the edge adjacent to the logic board void.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the card in to free the corner of the cell from adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pry gently to free the corner of the cell from the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the card under the opposite corner to detach yet more adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Give a final swipe to get the last of that stubborn adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
A final pry, and the card can be left in place to keep the battery propped away from the adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide the card under the center cell near the cable.
-
Insert the card near the far end of the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the bottom of the cell up from the case.
-
Pry the dock side corner of the cell up from the adhesive.
-
Pry again near the cable to loosen the cell further.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Slide a corner of the card under the top of the cell (the side adjacent to the logic board void).
-
Use the screw post as a pivot point to detach the last of the adhesive under the battery conector board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the cards at the junctures between batteries.
-
Pry upwards to free the battery connector board from the screw post and the battery assembly from the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift and gently remove the battery assembly from the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully peel up the dock connector and speaker cables to reveal the Wi-Fi antenna cable.
-
Peel the Wi-Fi antenna cable off the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following four screws:
-
Two 2.0 mm Phillips screws
-
Two 1.7 mm Phillips screws
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the Wi-Fi antenna off the speaker enclosure and remove it from the iPad 2.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the dock connector cable off the speaker cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of a plastic opening tool to peel up the edge of the large strip of tape securing the speaker assembly to the rear panel.
-
Use your fingers to peel the strip of tape off the speaker assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following two screws:
-
One 3 mm Phillips screw
-
One 2.1 mm Phillips screw
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of a plastic opening tool to help push the speaker assembly out from under the right side of the rear panel.
-
Remove the speaker assembly from the iPad 2.
-
Cancelar: No complete esta guía.
5 personas más completaron esta guía.