Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Llena una olla o cacerola con suficiente agua para sumergir completamente el iOpener.
-
Calienta el agua hasta que hierva. Apaga el fuego.
-
Coloca un iOpener en el agua caliente durante 2-3 minutos. Asegúrate de que el iOpener esté completamente sumergido en el agua.
-
Utiliza unas pinzas para extraer el iOpener calentado del agua caliente.
-
Seca bien el iOpener con una toalla.
-
Tu iOpener está listo para ser utilizado. Si necesita recalentar el iOpener, calienta el agua hasta que hierva, apaga el fuego y coloca el iOpener en el agua durante 2-3 minutos.
-
-
-
Utiliza una herramienta de expulsión de SIM o un clip desenrollado para expulsar la bandeja de la tarjeta SIM.
-
-
-
Si tu cristal de pantalla está agrietado, mantén una mayor rotura contenida y evita daños corporales durante su reparación pegando el vidrio.
-
Coloca tiras superpuestas de cinta de embalaje transparente sobre la pantalla del iPad hasta que toda la cara está cubierta.
-
Haz lo que puedas para seguir el resto de la guía según lo descrito. Sin embargo, una vez que el vidrio se rompe, es probable que continúe agrietándose mientras trabajas, y puede que tengas que usar una herramienta metálica para sacar el vidrio.
-
-
-
Hay una pequeña brecha en el anillo adhesivo del iPad en la esquina superior derecha del iPad, aproximadamente 2,0 pulgadas (~ 5 cm) desde la parte superior del iPad. Vas a explotar esta debilidad.
-
Alinea la herramienta con el botón de silencio. Inserta la punta de una herramienta de apertura de plástico en el hueco entre el cristal frontal y el bisel de plástico. Basta con insertar la punta de la herramienta de apertura, lo suficiente como para ensanchar la grieta.
-
-
-
Una vez que haya pasado la antena Wi-FI (aproximadamente 75 mm desde el borde derecho, o justo al lado del botón de inicio) vuelva a insertar la selección de apertura a su profundidad máxima.
-
Desliza la palanca hacia la derecha, liberando el adhesivo que sujeta la antena Wi-Fi al cristal frontal.
-
La antena está conectada a la parte inferior del iPad a través de tornillos y un cable. Este paso separa la antena del panel frontal, asegurando que al retirar el panel, la antena no se dañará.
-
-
-
Desliza la púa de apertura a lo largo del borde superior del iPad, tirando ligeramente hacia fuera para rodear el soporte frontal de la cámara.
-
El adhesivo a lo largo de esta sección es muy grueso, y puede requerirse una cantidad justa de fuerza. Trabaja con cuidado y lentamente, asegurándose de no resbalar y dañarse a sí mismo o a tu iPad.
-
-
-
-
Desliza la púa de apertura a lo largo del borde izquierdo del iPad, liberando el adhesivo a medida que avanza. El adhesivo es delgado debido al digitalizador a lo largo de todo el lado izquierdo. Asegúrate de que la púa no esté más de 10 mm dentro para evitar dañar el digitalizador.
-
-
Herramienta utilizada en este paso:Microfiber Cleaning Cloths$3.99
-
Sosteniendo el iPad por las esquinas superior e inferior derecha, gira el cristal delantero lejos del iPad.
-
Durante el montaje, utiliza un paño de microfibra y aire comprimido para limpiar el polvo o las huellas dactilares de la pantalla LCD antes de volver a instalar el cristal.
-
-
-
Solo queda el LCD.
-
La espuma que rodea la pantalla LCD debe sustituirse cuando se vuelva a instalar en otro dispositivo. Proporciona separación entre el digitalizador y la pantalla LCD, lo que ayuda a evitar el contacto "fantasma".
-
-
-
Utiliza el borde de una herramienta de apertura de plástico para levantar con cuidado las solapas de sujeción de las dos tomas ZIF del cable plano digitalizador.
-
-
-
Levanta la pantalla LCD por el borde largo más alejado del cable digitalizador y gírala suavemente hacia la carcasa trasera, como si estuvieras cerrando un libro.
-
Mientras mantienes levantada la pantalla LCD, desliza suavemente el panel frontal alejándolo del iPad. Ten cuidado de no enganchar el cable digitalizador en la carcasa trasera o en la pantalla LCD.
-
Vuelve a colocar la pantalla LCD en la carcasa para guardarla.
-
-
-
Levanta la pantalla LCD por el borde largo más cercano a los botones de volumen y sácala con cuidado de la carcasa trasera, como si pasaras la página de un libro.
-
Coloca la pantalla LCD boca abajo sobre una superficie limpia. Puedes apoyarla sobre un paño suave para evitar arañazos.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lay the LCD next to the rear panel.
-
Use a plastic opening tool to lift the display data cable lock upwards.
-
Pull the display data cable out of its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the LCD assembly from the rear panel assembly.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the edge of a plastic opening tool to flip up the retaining flap on the headphone jack and front camera cable ZIF socket.
-
Peel the headphone jack and front camera cable off the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the headphone jack and front camera ribbon cable straight out of its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the three 2 mm Phillips screws securing the SIM card slot to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 2.9 mm Phillips screws securing the headphone jack to the top edge of the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to help pull the headphone jack out of its recess in the top of the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the front camera and microphone cables off the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully remove the strip of tape covering the front camera cable connector.
-
Use a plastic opening tool to disconnect the front camera cable from the microphone cable immediately below it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the front camera cable off the microphone cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the front camera off the foam adhesive securing it to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the front facing camera cable out from the channel cut into the rear panel.
-
Remove the front facing camera from your iPad.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to disconnect the microphone cable connector.
-
Remove the headphone jack/SIM slot from the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If present, remove the piece of tape covering the end of the dock connector cable.
-
Use the edge of a plastic opening tool to carefully pry the dock connector cable's connector up from its socket on the logic board.
-
Peel the dock connector ribbon cable off the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place the prying tool beneath the 4 wires on the end of the connector and gently pry the speaker cable connector straight up from its socket on the logic board. Do not pry from the opposite end of the connector as this will break the 4 solder points on the underside of the socket and will require a microsolder repair.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to flip up the retainer securing the upper component board cable connector to its socket on the logic board.
-
Pull the connector away from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 2.1 mm Phillips screws securing the logic board bracket to the rear case near the digitizer cable socket.
-
Remove the logic board bracket from the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the four 2.6 mm Phillips screws securing the logic and communications boards to the rear panel.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to gently pry the logic board up from the rear case.
-
The logic board is adhered to the rear case; work slowly and uniformly to peel up the glue without damaging the board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board out from the rear case, and rotate it slightly toward the battery.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to disconnect the cellular data antenna cable from its socket on the communications board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.1 mm Phillips screw securing the cellular data antenna cable to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to remove the two pieces of tape.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the cellular data antenna from the rear case with a plastic opening tool.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the cellular data antenna out of its recess in the iPad casing.
-
Gently pull the cellular data antenna cable through the channel cut in the rear panel, and remove the antenna from the device.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a plastic opening tool to disconnect the right antenna cable from its socket on the communications board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 2.1 mm Phillips screw securing the right cellular antenna to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to start each piece, and then the flat end to smoothly peel the tape up without tearing it.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently pry the antenna from the rear case with a plastic opening tool.
-
Lift and remove the right cellular data antenna from the iPad 2.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove any tape covering the GPS antenna ZIF connector.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to flip the retaining tab on the ZIF connector to release the GPS cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place a reheated iOpener on the top edge of the iPad to soften the adhesive holding the GPS antenna to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the pointed end of a spudger under the GPS cable from the interior of the antenna recess.
-
Pull the spudger toward the top edge of the case to thread the cable out of the slot from the main body of the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Using a set of tweezers, gently lift the GPS antenna cable to begin peeling the antenna off of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Place the flat end of a spudger under the freed end of the GPS antenna.
-
Push the spudger under the antenna sticker to separate the adhesive holding it to the case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Continue to push the spudger under the antenna to clear it of adhesive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
As soon as you can grip the GPS antenna with your fingers, peel it up off the rear case to remove it.
-
Cancelar: No complete esta guía.
7 personas más completaron esta guía.