Repara tus cosas

Derecho a reparar

Partes y herramientas

iMac Intel 21.5" EMC 2428 Display Replacement

Escrito Por: Walter Galan (y 6 de otros participantes)
  • Comentarios: 57
  • Favoritos: 16
  • Terminaciones: 25

Dificultad

Moderar

Pasos

9

Tiempo Requerido

Sugerir un tiempo??

Secciones

2

Banderas

0

Introducción

Remove the LCD to access most of your iMac's internals.

  1. Before beginning, unplug your iMac and lay it on a soft surface as shown. Stick a suction cup near each of the two top corners of the glass panel.
    Herramienta utilizada en este paso:
    Heavy-Duty Suction Cups (Pair)
    $14.99

    • Before beginning, unplug your iMac and lay it on a soft surface as shown.

    • Stick a suction cup near each of the two top corners of the glass panel.

    • To attach the suction cups we sell, first position the suction cup with the movable handle parallel to the face of the glass panel. While lightly holding the suction cup against the glass, raise the movable handle until it is parallel with the other handle.

    • If your suction cups refuse to stick, try cleaning both the glass panel and the suction cup with a mild solvent.

    Editar

  2. Gently lift the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the top edge of the glass panel. Pull the glass panel away from the lower edge of the iMac and carefully set it aside.

    • Gently lift the glass panel perpendicular to the face of the LCD enough to clear the steel mounting pins attached along the underside of the top edge of the glass panel.

    • Pull the glass panel away from the lower edge of the iMac and carefully set it aside.

    • During reinstallation, be sure to meticulously clean the inside of the glass panel and the face of the LCD as any dust or fingerprints trapped inside will be annoyingly visible when the machine is turned on.

    Editar

  3. Remove the eight 8 mm T10 Torx screws securing the display to the outer case. The last two pictures are detail shots of each side of the display. The last two pictures are detail shots of each side of the display.

    • Remove the eight 8 mm T10 Torx screws securing the display to the outer case.

    • The last two pictures are detail shots of each side of the display.

    Editar

  4. Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

    Kits para Nintendo Switch

    Una solución rápida para volver al juego

    Comprar kits de Switch

  5. Slightly lift the top edge of the display out of the outer case.

    • Slightly lift the top edge of the display out of the outer case.

    • Do not lift it too much. There are several cables attaching the display to the logic board. Twisting or pulling the display assembly with the cables attached will damage your iMac.

    Editar

  6. Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac. Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac.

    • Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac.

    Editar

  7. Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board. Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).

    • Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board.

    • Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).

    Editar

  8. Grab the plastic pull tab secured to the display data cable lock and rotate it towards upwards. Pull the display data cable straight out of its socket on the logic board. Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

    • Grab the plastic pull tab secured to the display data cable lock and rotate it towards upwards.

    • Pull the display data cable straight out of its socket on the logic board.

    • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

    Editar

  9. Disconnect the LCD thermal sensor cable connector from its socket on the logic board. Disconnect the LCD thermal sensor cable connector from its socket on the logic board.

    • Disconnect the LCD thermal sensor cable connector from its socket on the logic board.

    Editar

  10. Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.

    • Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.

    Editar
Conclusión

To reassemble your device, follow these instructions in reverse order.

25 personas más completaron esta guía.

4 comentarios

Agregar un comentario

My screen does not come on but the dvd player powers up and the orchestral noise in the beginning sounds what do you think the problem is?

Dave Seawater - Contestar

I can't seem to get that flat gold color wire to go back into the socket....please help. I'm at mikichan1@yahoo.com

mikichan1 - Contestar

I had the same problem. Frustrating.

garyledet - Contestar

I actually messed up my lcd cable end, so make sure its aligned properly before you try to insert it. If not you will be waiting 3 days like me for the replacement cabe to arrive.

Tony J - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 14

Ultimos 7 días: 67

Ultimos 30 días: 310

Todo El Tiempo: 34,994