Saltar al contenido principal
  1. Antes de empezar, desconecte su iMac y recuestela sobre una superficie suave. Adhiera una ventosa en los 2 angulos superiores del panel de vidrio.
    • Antes de empezar, desconecte su iMac y recuestela sobre una superficie suave.

    • Adhiera una ventosa en los 2 angulos superiores del panel de vidrio.

    • Para pegar las ventosas primero posicione sus manijas paralelas al borde del panel de vidrio. Presione suavemente las ventosas contra el vidrio y gire las manijas de vacio hacia el panel de vidrio.

    • Si sus ventosas no se pegan, limpie la superficie del vidrio y la goma de sus ventosas con un solvente liviano.

    • Insertar traducción aquí

    • Insertar traducción aquí

  2. Tire despacio el panel de vidrio perpendicular a la cara del LCD con cuidado ya que hay pestañas de metal en la parte inferior del panel de vidrio. Remueva el panel de vidrio hacia arriba sacando cuidadosamente las pestañas de acero y coloque sobre una superficie limpia.
    • Tire despacio el panel de vidrio perpendicular a la cara del LCD con cuidado ya que hay pestañas de metal en la parte inferior del panel de vidrio.

    • Remueva el panel de vidrio hacia arriba sacando cuidadosamente las pestañas de acero y coloque sobre una superficie limpia.

    • Durante la reinstalación, asegurese que la cara interior del panel de vidrio esta perfectamente limpia y que no haya quedado suciedad ni impresiones de dedos sobre el LCD ya que seria visibles al encender el iMac.

  3. Este paso está sin traducir. Ayuda a traducirlo

    Remove the eight 8 mm T10 Torx screws securing the display to the outer case. The last two pictures are detail shots of each side of the display. The last two pictures are detail shots of each side of the display.
    • Remove the eight 8 mm T10 Torx screws securing the display to the outer case.

    • The last two pictures are detail shots of each side of the display.

  4. Este paso está sin traducir. Ayuda a traducirlo

    Slightly lift the top edge of the display out of the outer case.
    • Slightly lift the top edge of the display out of the outer case.

    • Do not lift it too much. There are several cables attaching the display to the logic board.

  5. Este paso está sin traducir. Ayuda a traducirlo

    Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac. Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac.
    • Pull the vertical sync cable connector out of its socket on the LED driver board near the top left corner of your iMac.

  6. Este paso está sin traducir. Ayuda a traducirlo

    Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board. Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).
    • Rotate the display out of the outer case enough to disconnect the LED backlight power cable from the LED driver board.

    • Disconnect the LED backlight power cable by depressing the locking mechanism while pulling the connector away from its socket (toward the bottom edge of the iMac).

  7. Este paso está sin traducir. Ayuda a traducirlo

    The display data cable plug has a wire lock.  Disengage the plug's lock by rotating the plastic tab so that it points upward.  (It is not a pull tab.) Pull the display data cable straight out of its socket on the logic board.
    • The display data cable plug has a wire lock. Disengage the plug's lock by rotating the plastic tab so that it points upward. (It is not a pull tab.)

    • Pull the display data cable straight out of its socket on the logic board.

    • Do not lift up on the display data cable, as its socket is very fragile. Pull the cable parallel to the face of the logic board.

  8. Este paso está sin traducir. Ayuda a traducirlo

    Disconnect the LCD thermal sensor cable connector from its socket on the logic board. If your fan is spinning full speed after completion, check this connection or the hard drive's thermal sensor cable.
    • Disconnect the LCD thermal sensor cable connector from its socket on the logic board.

    • If your fan is spinning full speed after completion, check this connection or the hard drive's thermal sensor cable.

  9. Este paso está sin traducir. Ayuda a traducirlo

    Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.
    • Carefully pull the display toward the top edge of your iMac and lift it out of the outer case, minding any cables that may get caught.

Linea de Meta

29 personas más completaron esta guía.

I damaged the lcd frame (with magnets) and I don't know where to find it. Can you guys help?

It's just the frame with magnets that attaches the lcd screen...

fredericoconchinha - Contestar

hey thanks for this.... i had to swap LCDs due to well known streak/screen fault.

after over 2 years using external display for work, i saw this blog and thought i might try.

the stakes were extremely high (my wife's iMac and no cash to get OOW apple repair, but your help got me through it. super cheers.

NB. i found this other thread most helpful re: the side strips that screw to the LCD panel and the iMac chassis.

Limpieza del LCD en el iMac

rob - Contestar

Hey

where can I buy the LED backlight power cable from step 6

thanks

Swiss - Contestar

I'd like to buy IMAC LCD Model: ME086ZP/A. Where can I buy this item?

Ellen Laserna - Contestar

Hi, is that possible to replace the LCD diaplay by a 4k display?

J.J. JIANG - Contestar

Agregar Comentario

Ver Estadísticas:

Ultimas 24 horas: 7

Ultimos 7 días: 68

Ultimos 30 días: 246

Todo El Tiempo: 60,082