Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Loosen the three Phillips screws securing the access door to the bottom edge of your iMac.
-
Remove the access door from your iMac.
-
-
-
Adhiera una ventosa en los 2 angulos superiores del panel de vidrio.
-
Si sus ventosas no se pegan, limpie la superficie del vidrio y la goma de sus ventosas con un solvente liviano.
-
Insertar traducción aquí
-
-
-
Retira los ocho tornillos Torx T10 de 8 mm que sujetan la pantalla a la carcasa exterior.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following four screws securing the power supply to the outer case:
-
Two 22.2 mm fine-thread T10 Torx
-
One 25 mm coarse-thread T10 Torx
-
One 9 mm coarse-thread T10 Torx
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully lift the power supply out of the outer case and rotate it to expose the cable lock as shown, minding the DC-Out cable still attaching it to the iMac.
-
Disconnect the DC-In cable by depressing the locking mechanism on the connector while you pull the connector away from its socket on the power supply.
-
Once the locking mechanism has cleared the socket, pull the DC-In connector away from the power supply.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the AC-In cable by depressing the locking mechanism while pulling the connector away from its socket.
-
Remove the power supply from the outer case.
-
-
-
Saca el conector del sensor térmico de la unidad óptica directamente de su zócalo en la placa lógica.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single 13 mm T10 Torx screw securing the optical drive fan to the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the optical drive off the pins attached to the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the optical drive fan connector away from its socket on the logic board.
-
Remove the optical drive fan from the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the left and right speaker connectors toward the right side of the iMac to disconnect them from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the audio port cable by pulling its connector toward the right side of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the AirPort cable by lifting its connector off the socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the following cables by pulling their connectors toward the top edge of the iMac:
-
Camera cable
-
Hard drive thermal sensor
-
Hard drive fan
-
Microphone
-
Disconnect the following cables by pulling their connectors toward the right edge of the iMac:
-
Ambient temperature sensor
-
Bluetooth cable
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the CPU fan and power button by pulling their connectors toward the left edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If present, remove the piece of tape covering the IR sensor connector.
-
Disconnect the IR sensor by pulling its connector toward the top edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use your fingers to lift IR sensor assembly straight up out of the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following six screws securing the logic board to the outer case:
-
Three 25 mm T10 Torx
-
Two 21.5 mm T10 Torx
-
One 7 mm T10 Torx
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the plastic ducts from the side of the LED driver board and the hard drive by pulling them away from the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully remove the aluminum tape attaching the GPU heat sink to the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Carefully pull the logic board slightly away from the outer case.
-
While holding the board away from the outer case, rotate the board back and forth while lifting up to release it from the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Now that the lower edge of the board is free from the outer case, rotate the logic board toward yourself to expose its rear face.
-
Carefully pull the optical drive connector away from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the DC-In cable from the logic board by simultaneously depressing the locking lever on the connector while pulling it away from its socket.
-
Remove the logic board from the outer case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to pry the PRAM battery out of its socket on the logic board.
-
Cancelar: No complete esta guía.
30 personas más completaron esta guía.
14 comentarios
Dank dieser Anleitung hat der Wechsel der Pufferbatterie problemlos funktioniert.
Schaut man selbst in das innere eines iMac, wird einem erst richtig bewußt welche Genialität hinter dieser Erfindung steckt.
Danke Steve
Stupid design. A battery must be accessible from the outside or should last forever!
It was easier than I thougth, my iMac was acting weird with a dead Pram battery, great guide!!...thanks a lot iFixit!