Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
-
Apoya tu iMac con la pantalla hacia abajo y con la parte inferior mirando hacia ti.
-
Soltar el unico tornillo Phillips ubicado en el centro de la trampilla de acceso
-
Quitar la trampilla de acceso del iMac
-
-
Herramienta utilizada en este paso:Heavy-Duty Suction Cups (Pair)$14.95
-
Coloca dos ventosas en las esquinas opuestas del panel de cristal.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 12 screws securing the front bezel to the rear case:
-
Eight 13 mm T8 Torx.
-
Four 25 mm T8 Torx.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the front bezel from its top edge off the rear case.
-
Once the top edge of the front bezel has cleared the rear case, rotate the front bezel toward the stand and lift it off the rear case.
-
Rotate the front bezel away from the rest of the device and lay it above the top edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the microphone cable connector, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the LCD temperature sensor connector straight up off its socket on the logic board.
-
(located at the top of the logic board on the 24")
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T6 Torx screws securing the display data cable to the logic board.
-
Use the attached black tab to pull the display data cable connector straight away from the logic board.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the eight T8 Torx screws securing the display panel to the rear case.
-
Lift the display panel from its left edge and rotate it toward the right edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With the display panel still lifted, disconnect the four inverter cables.
-
(combined into one plug in on the 24")
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel the strip of EMI tape off the edge of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T10 Torx screws securing the optical drive to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, remove the piece of tape holding the thermal sensor wires to the hard drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the optical drive thermal sensor connector straight away from its socket on the logic board.
-
When removing this connector, it is helpful use your thumbnails to push the ears on either side of the connector toward the top of your iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the left edge of the optical drive slightly and pull it away from the right side of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert a spudger between the optical drive connector and the optical drive.
-
Twist the spudger to slightly separate the optical drive connector from the optical drive, then use your fingers to pull the connector away from the drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the piece of foam tape covering the optical drive thermal sensor.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
To remove the optical drive thermal sensor, use the tip of a spudger to lift the center finger of the thermal sensor bracket while applying slight tension to the thermal sensor cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the optical drive thermal sensor bracket up off the adhesive securing it to the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use a spudger to remove the small piece of EMI foam from the bottom of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T10 Torx screws from both sides of the optical drive (four screws total).
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the tip of a spudger to press each of the optical drive bracket tabs out of their slots on the bottom of the optical drive.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Rotate the optical drive bracket slightly away from the optical drive.
-
Pull the optical drive bracket away from the open end of the optical drive, minding any tabs that may get caught.
-
Cancelar: No complete esta guía.
12 personas más completaron esta guía.