Esta versión puede contener ediciones incorrectas. Cambiar a la última instantánea verificada.
Qué necesitas
-
-
Apoya tu iMac con la pantalla hacia abajo y con la parte inferior mirando hacia ti.
-
Soltar el unico tornillo Phillips ubicado en el centro de la trampilla de acceso
-
Quitar la trampilla de acceso del iMac
-
-
Herramienta utilizada en este paso:Heavy-Duty Suction Cups (Pair)$14.95
-
Coloca dos ventosas en las esquinas opuestas del panel de cristal.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following 12 screws securing the front bezel to the rear case:
-
Eight 13 mm T8 Torx.
-
Four 25 mm T8 Torx.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the front bezel from its top edge off the rear case.
-
Once the top edge of the front bezel has cleared the rear case, rotate the front bezel toward the stand and lift it off the rear case.
-
Rotate the front bezel away from the rest of the device and lay it above the top edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the microphone cable connector, removing tape as necessary.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Pull the LCD temperature sensor connector straight up off its socket on the logic board.
-
(located at the top of the logic board on the 24")
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two T6 Torx screws securing the display data cable to the logic board.
-
Use the attached black tab to pull the display data cable connector straight away from the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the eight T8 Torx screws securing the display panel to the rear case.
-
Lift the display panel from its left edge and rotate it toward the right edge of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
With the display panel still lifted, disconnect the four inverter cables.
-
(combined into one plug in on the 24")
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the single T10 Torx screw securing the right speaker to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the right speaker cable connector from the audio board by pulling it straight up from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the optical drive fan connector from the audio board by pulling it straight away from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the optical drive fan off the plastic posts protruding from the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Insert the flat end of a spudger into the gap between the optical drive data cable connector and its socket.
-
Twist the spudger to separate the connector from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the microphone cable connector from the audio board by pulling it straight up from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the following connectors:
-
Hard drive thermal sensor cable.
-
Optical drive thermal sensor cable.
-
Hard drive fan cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the DC-in cable by simultaneously depressing both locking arms and pulling its connector away from the socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Metal Spudger$2.99-
Pull the SATA data cable straight up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry both antenna connectors up off the AirPort Extreme card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the left speaker connector from the audio board by pulling it straight away from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
De-route the left fan cable from the channel on the CPU fan.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the following connectors:
-
Ambient temperature sensor cable.
-
Power button cable.
-
CPU fan cable.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the camera cable connector from the logic board by pulling it straight up from its socket.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the bluetooth antenna connector up off the bluetooth board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the sharp end of a spudger to peel the EMI tape off the headphone/microphone jacks.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following screws securing the logic board to the rear case:
-
Three fine-thread T10 Torx.
-
Six coarse-thread T10 Torx.
-
One longer coarse-thread T10 Torx.
-
Two coarse-thread T8 Torx.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the logic board assembly out of the rear case, minding any cables or I/O ports that may get caught.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Gently lift the hard drive fan off the plastic pins protruding from the lower case.
-
Cancelar: No complete esta guía.
3 personas más completaron esta guía.