Esta versión puede contener ediciones incorrectas. Cambie a la última instantánea verificada.
Qué necesitas
-
Este paso está sin traducir. Ayuda a traducirlo
-
Loosen the two captive Phillips screws securing the access door to the iMac.
-
Remove the access door from the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the following four screws:
-
Three 6 mm T8 Torx.
-
One 8 mm T8 Torx.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Flip your iMac over and lay it stand-side down on a flat surface.
-
To lift the front bezel off the iMac, simultaneously:
-
Use your thumbs to press in the RAM arms and hold the iMac down.
-
Use your index fingers to pull the small bridge of material on the front bezel toward yourself.
-
Pull the Front bezel up with your index fingers.
-
Once the small bridge of material has cleared the RAM arms, lift the front bezel by its lower edge just enough to clear the bottom edge of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Plastic Cards$2.99-
Insert a plastic card up into the corner of the air vent slot near the top of the rear case.
-
Push the card toward the top of the iMac to release the front bezel latch.
-
Pull the front bezel away from the rear case.
-
Repeat this process for the other side of the front bezel.
-
If the bezel refuses to release, try pressing the lower edge back onto the rear case and repeat this opening process.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lay your iMac stand-side down on a table.
-
Lift the front bezel from its lower edge and rotate it away from the rest of your iMac, minding the RAM arms that may get caught.
-
Lay the front bezel above the rest of the iMac.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
If necessary, remove the piece of kapton tape(it is ok to toss this) wrapped around the microphone and camera cables.
-
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the two 4.8 mm T6 Torx screws securing the display data cable to the logic board.
-
Grab the display data cable connector by its black tab and pull it straight up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Inverter cable on 24inch iMac pulls off to the left.
-
Pull the inverter cable connector straight up off its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Peel back the aluminum EMI tape from the two vertical edges of the display.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:TR10 Torx Security Screwdriver$5.99-
Remove the four 8 mm with 2 mm thick head coarse-thread T10 Torx screws securing the display to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the display from its lower edge and pull it toward yourself to peel off the EMI shield attached to its top edge.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 30 mm T10 Torx screw securing the left speaker to the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Remove the 17 mm T10 Torx screw from the right speaker.
-
-
Este paso está sin traducir. Ayuda a traducirlo
Herramienta utilizada en este paso:Metal Spudger$2.99-
Pull the SATA data cable connector away from its socket on the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the CPU fan by pulling its connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the hard drive power cable by pulling its connector up off the logic board.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Use the flat end of a spudger to pry the AirPort Extreme antenna connector up off the AirPort Extreme card.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Lift the left and right speakers out of the rear case.
-
-
Este paso está sin traducir. Ayuda a traducirlo
-
Disconnect the speaker cable connector by pulling its connector away from the socket on the logic board.
-
Cancelar: No complete esta guía.
Una persona más ha completado esta guía.